6651597299 Kenmore Dishwasher - Instructions

At first I thought I needed a new bottom rack for my dishwasher. Out of curiosity, I watched the installation video and realized that the Tine Row installed separately and that was the only part I needed. I am appreciative of being able to access that video and the money I saved. Installation took seconds to complete.

There was no tools involved the part popped right into place. I received the part within two days from the date placed. It was great.

Remove bottom valence to get access to 2 screws on the bottom flange of front cover. With those 2 screws removed the front panel comes off revealing the rear side of the dispenser and 6 screws that hold dispenser tightly to the inside panel. Remove 2 wires that are push connectors to solenoid. The unit simply drops out. Installation is just the reversal of removal. Very easy.

I screwed the rack mount to the spindle using
the extra screw I ordered. I removed the upper dishrack's front stops and slid the rack
out. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.

I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.

I first had to take the upper drawer of the dishwasher out so that I could get to the faulty part. This was a little tricky as there were two clips that had to be removed from the arm slides before the upper drawer could be removed.
I then realized that the faulty part DID NOT exactly match the repair part I received. The original connection wand was in two pieces where the repair part was all one piece. That required a bit of thought before I began the repair. There was NO drawing accompanying the new part, so I had to decide how the part would be connected. After a little trial and error, I determined the arrangement of the repair part and completed the repair. All in all, it went well, but there was a few anxious moments when I first saw the difference between the original part and the new part.

replaced those parts... but lingering doubts about adequacy of water supply due to sediment primarily from old iron pipes, evidenced in faucet aerator. So I added a Rusco hot water sediment trap filter to the supply line leading to the dishwasher and faucet, along with a new flex supply line to the dishwasher. Water supply seems improved, and any potential sediment will be caught by the trap.The time, tools, and complexity of adding the hot water sediment filter are not covered in the above.

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

The nut had broken off even with the top of the threaded area, so we had to remove that broken part. We did so by using small pliers and inserting them in the opening and held them in a spreaded position while turning the broken piece out. We replaced the three new parts and put it back together and it works fine. So easy and much cheaper that having a repairman come in. Took us less than 15 minutes.

First I replaced the lower door seal then I replaced the door gasket. The instructions were clear so both were pretty easy. Unfortunately neither fixed the leak. After further research I discovered that the screws on the pump had become loose. I used a torx driver to tighten the screws. Time will tell, but I am pretty confident that this has fixed the problem.

The new part was one piece and merely took unscrewing the holder and replace the part. Except for the screw being tough to remove, putting it back on was a snap!

required NO tools,

just unscrew the large thumb screw, and replace the washer arm bearing!

problem solved like that!

maybe a 5 min job. part was a perfect match.

Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.

I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts

I went back to the web site to make sure I'd ordered the right part.?? looked at the diagram and then watched your little video.?? He had the part hooked opposite of what was shown. (The arm wouldn't rotate) So I turned it arround. While he was still??. It took me less that 5 min and the dishwasher is working Great.????

First, I removed the tines which were still connected to the top rack by the unbroken parts of 3 clips. (The part of the clip which is subject to breakage is the top, where it allows the tines to be clipped up or released and laid down.) I left the broken clips on the rack as a guide to where to install the new ones. I then attached the new clips to the tines, which is like assembling a puzzle. It would be helpful to replace one clip before all 3 break, so you have an illustration, but it's fairly easy to figure out how to attach the clip as long as you realize the tines need to be released and folded down, or clipped in the up position. With all 3 clips attached to the tines, simply pop the broken clips off the rack and attach the tines to the rack with the new clips. I appreciate the advice from the users who warned against breaking the clips with a tool. It's not really necessary to soak them in hot water. My advice is to use only fingers for installation. Brute force is not necessary... just position and pinch.