66512782K311 Kenmore Dishwasher - Instructions

Pretty easy for the parts. Taking the dishwasher out is the hard part. Typically, you should be able to unscrew the 2 screws holding the dishwasher to the underside of the countertop and then slide out the dishwasher to expose the cable assembly - but you also need to unplug the unit (unless it is hardwired), disconnect the hot water supply line from the angle stop (remember to turn off the angle stop) and sometimes disconnect the drain line from the vacuum breaker or garb disposal. You need to disconnect these things so that you can move the dishwasher out far enough to be able to see the entire right and left sides of the dishwasher. Once that hard part is done, you use a hex driver to remove the old cable pulleys, put on the new cable pulleys, and then feed the light weight cable through the pulleys - the end with the big plastic thingie attaches to the door and the other end attaches to the spring. Then you grab the spring and manhandle it onto the back end of the dishwasher chassis (look for the small hole in line with where the cable would line up. Careful as the spring attachment step could result in an injury - Hope this helps.

Received the part. No instructions came with it. Luckily it was pretty simple to figure out. i removed the appliance from under the counter, saw how the part was attached on the other side and simply replaced the other side that was broken. Easy.

Disconnect top screws
Pull dishwasher out halfway
Notice how the other side is connected
Thread cord, use pliers to pull spring to connect.

First I turned off the water and power to the dishwasher.I removed the two screws on the front bottom cover plate, removed the plate. Removed the two nuts and bolts holding the dishwasher in place between the cabinets. Then I pulled the dishwasher out about 6 to 7 inches so I could see the spring, pulley and rope connections. Then I saw the rope on the right side of the door bottom had pulled through the connector. I ordered the part and next day delivery was great.(excellent service). The repair kit comes with both sides parts but I only needed one(for now). I reconnected spring to rope connector and threaded through pulley and to the door and job was done. A little difficult stretching spring so I put a long piece of wire to hold spring tight while connecting to rope but I worked out great. My husband said "great job, honey". I saved a $150 repairman bill....now I might go shopping (ha ha) Kim

The repair itself was relatively easy. I basically only had to remove the two screws that were securing the diswasher to the cabinetry, disconnected the water line and extended the diswasher out approximately 10 inches. I then replaced the part by hooking the new cable assembly to the spring and using pliers expanded the spring so I could snake the other end of the cable through the pulleys and attach it to the door. The otherside was my guide. This part should be modified to replace the two plastic ends with metal counterparts. This would allow the part to have a longer life especially in my case since the plastic end broke and not the cable itself.

Removed the bottom cover plates.
Removed the screws holding in the dishwasher.
Removed old single moving roller and replaced with newly designed double rollers.
Installed link(string).
Replaced other side rollers and link.
Reinstalled dishwaser.

Unscrewed mounting screw at top and bottom of duahwasher, pulled out dishwasher could see the pully on one side had broken. installed new part put dishwasher back in place and rescrewed mounting screws.

just move the machine out and replace the string. this site is very reliable and and great company. since the dishmachine door cannot be closed, we first order door strike, ,,,, still doesn't work after installation. and return all parts and order the balance kit, now works fine after. we appreciate your help

Followed directions here. Extremely easy repair.

I replaced the thermostat (part # PS11750035) along with the heating element (part # PS9494999) and the turbidity sensor (part # PS11757214). I also checked the filter (part # PS11759673) and it was very clean with no holes. The dishwasher still has water and soap suds standing in dishwasher after I ran it through different cycles. Also, when I run the sanitize cycle the sanitize light flashes red at the end. It doesn’t appear to completely filling with water. Also my hot water temperature is 130 degrees after running for 1 minute. I am at a loss! Any suggestions?

Installation went easy your how to tutorial video was spot on perfect

Unplugged dishwasher and turned off water supply. Removed bottom panel. Put rag under valve and unscrewed water inlet. Used ratchet and socket to remove screw from valve. Disconnected wires. Disconnected outlet. Installed new valve opposite of disassembly. Turned water back on. Plugged in and checked for leaks. Test ran.

The hardest part was pulling the unit out. Ours required the electric to be disconnected. First turn off breaker, then disconnect electric, then remove the 2 screws in the sides that keep it in place (located on top for non-stone counter). Slide unit out. Next remove the spring and connect the loop from the link to the spring. The other end of the spring goes in the hole next to the rear leg. Pull the string so there is enough slack to loop the spring aroung both pulleys and then slide the end over the hook on the bottom of the door. Use the other side as a guide. Slide unit back, hook up electric, replace mounting screws. Turn on breaker.

last time this piece broke, I called a tech and $150 to fix. I am not much of a do-it-yourselfer, but this was very easy. Removed to screws. I then pulled out dishawasher from cabinet. Removed plastic piece, replaced part, pushed dishwasher back and put in screws.

Easy, easy, easy. Appliances use to be built with metal parts that did not break as often.

Pulled dishwasher from under the counter and replaced the plastic part with the new part and attached the new cord to the door spring and to the replacement plastic part. replaced the dishwasher under the counter and replaced the kick plate. All Done.