JDB1060AWS Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donna from LAWRENCEBURG, KY
- Parts Used:
- 12002709
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
no lights on front panel
Shut off power to dishwasher, remove screws holding panel to door , move panel enough to get to circuit board. Remove three nut drivers screws, unplug cables from circuit board. Remove circuit board by unsnapping from side ears, replace new circuit board, plug in cables. secure with screws, secure door panel. put power back to dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from henderson, NV
- Parts Used:
- WP99003317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
detergent dispenser door latch not holding
from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Lansing, MI
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
the dishwaster was not getting the dishes clean
The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Rockaway, NJ
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
rinse dispenser was clogged and unusable.
I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.
The new part arrived quickly and was the perfect match.
The new part arrived quickly and was the perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold L. from winamac, IN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle stopped engaging
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LeRoy D from WAYNESVILLE, MO
- Parts Used:
- WPW10130695
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Latch loose
Remove inside cover and eight screws. Unplug two electrical connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Burlington, MA
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking do to heating element decay.
1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Gardner, KS
- Parts Used:
- 6-917696
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher Stainless Steel Face Panel
Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Amarillo, TX
- Parts Used:
- WP99002751
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
START LIGHT WOULD JUST BLINK AND WOULD NOT DRAIN, JUST BLINK
Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eva from columbus, OH
- Parts Used:
- WPW10192799
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
accumulator filter
Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fayetteville, GA
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper wash arm would not turn.
Snapped the old part out and snapped the new part in.
It was a piece of cake.
It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Kopperl, TX
- Parts Used:
- 99002644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The striker broke when repairing something else.
I pulled the machine from under the counter top and the striker is right in front just under the insulation. I pullled the insulation back just a little and screwed down the new striker plate. That's all. I moved the machine back uinder the counter and secured it. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from STREATOR, IL
- Parts Used:
- WP99003149, WP99003148
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Upper dish-rack had broken wheel which holds the rack in the track, without the wheel the rack continually fell down. The lower rack had a broken wheel attachment which sometimes led the rack to become derailed.
I used a flat screwdriver and small forceps pliers to remove the broken wheel on the lower rack, followed the online video and it was done in a few moments. On the upper one I removed the end piece using small forceps pliers then removed the broken wheel. I used the flat screwdriver to ease the new wheel assembly on the the rack, engaged it in the track then replaced the end piece on the track and the repair was complete. I did order 2 of each item to keep as spare for the next repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from mount airy, MD
- Parts Used:
- WPW10130695
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher handle had problems opening and closing
1) Turned off the power
2) I removed the screws on the plastic door.
3) The latch/handle assembly was right there.
4) I noticed that white and black wires fed each side. I noted which side did the black feed and the white feed.
5) I took a pair of pliers and held the white wire brackets and pulled the metal parts off. This is where the time took.
It took about 2 minutes per side.
6) I then slid the new metal parts in the white brackets.
7) I screwed it back.
8) Turned it back on!
9) Works great
2) I removed the screws on the plastic door.
3) The latch/handle assembly was right there.
4) I noticed that white and black wires fed each side. I noted which side did the black feed and the white feed.
5) I took a pair of pliers and held the white wire brackets and pulled the metal parts off. This is where the time took.
It took about 2 minutes per side.
6) I then slid the new metal parts in the white brackets.
7) I screwed it back.
8) Turned it back on!
9) Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Centreville, VA
- Parts Used:
- WP99003149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two broken lower rack wheels
It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol
Was this instruction helpful to you?
Thank you for voting!