JDB3000AWS3 Jenn-Air Dishwasher - Instructions

I followed another story for the same repair. Worked great.

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

Note orientation of the old gasket before removing it, so you can put the new one in right. Pull the old one out, which is a snap. Mark the center of the new one and push the center into the channel with your thumb nail at the top middle of the machine. Continue pushing it in on both sides, from top to bottom, in a steady, fluid motion; don't stretch it. If there is a bit extra at the ends, cut it off with a scissors, being conservative so you don't cut it too short. The new gasket will make the door a bit harder to close, but that's what you want.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

Repair man said I needed a new pump and would cost $350 to repair. This dishwasher was only 5 years old and we only use about once a week so didn't think the pump was gone. Went on this website and read some stories. this model has a mini garbage disposal with a chopper and screen which gets clogged up and prevents water from circulating. You can clean the screen without removing the dishwasher. Remove the cover plates on the bottom with 4 screws and the smaller cover plate underneath. Remove screen, clean and replace. If the chopper is broken you can order a replacement for $21. There is another story on this site with a lot more detail so I wont repeat here.

I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.

The first try didn't go well. The door didn't stay locked because the new seal was preventing it.
I pulled it back off for the second try and first I let it soak in the hot water for a few minutes to soften the rubber. Then I lubricated it with Vaseline and now the seal got in the grove easily and completely. I believe that that step was critical to ensure 100% success rate. After that everything was fine, the door locked properly, and, of course, there was no more leaking.

remover the nut inside of the dishwasher under the float took bottom plate off open the plastic housing installed new the new float switch plug in the wires snip in the new housing put the unit back in the hole put nut back on and put the bottom plate back on easy as pie

Used bowls in upright position in upper shelf determining no water to upper shelf after running in rinse cycle. Added a cup of Vinegar in rinse cycle. Performed bowl test in upper rack & still no water in bowls. Dismantled inside of unit by removing both spray arms & found lower seal deteriorated & upper seal in need of replacing. Replaced seals & redid bowl test & found no water getting to top rack still. Found utube vid showing removing garbage disposal portion of unit. Requires removing screen in bottom of dishwasher. One screw attaches garbage disposal cover. Found non food items & food by broken garbage disposal. Repaired disposal, removed debri & reinstalled all components. Redid bowl test in upper shelf & bowls were overflowing!!????Dishwasher works GREAT now & can hear garbage disposal operating along with massive water being sprayed!!!

At first, I figured the noise was coming from underneath, and took off the bottom front plate. I noticed there was a leak from the center of what I later learned was the "pump" assembly. So I unplugged the dishwasher, disconnected the water and drain from under the sink, unscrewed the screws holding it under the counter, and pulled it out from under the cabinet. Then I laid it on its back, and realized where the leak was coming from. At this point, I thought the noise had been coming from the motor. So I detached the motor (required use of a socket, and realized it was "free", so thought the problem must be further up inside. Reached my fingers in where the motor mounts and found part of the chopper assembly. The "chopper" had torn itself free from the screen. Realized at that moment I needed to disassemble the pump from the top. Took off water distribution system, bottom water rotor, pump plate (required use of "star" screwdrivers, two different sizes), foreign object plate, and chopper assembly cover. Getting the chopper assembly cover off was hard; had to pry it with sharp l-shaped poker; it was adhered with calcium deposits. Finally got it off, found rest of chopper assembly (screen with hole in the middle where chopper had been), ordered chopper from PartSelect, took 3 days, installation was easy, the reverse of removing it. (It is not necessary to remove motor to replace chopper assembly.) However, it is still leaking from the bottom, and I'm at a loss as to how to fix that.

Long story short, noticed one of two leaks and came to conclusion there is no workaround since sump pump gasket seems to be hermetically sealed to sump pump. Which is understandable because of water in area. Wife helped by soaking other parts that were removed and replaced, because of calcium buildup. Which we hope will extend life of dishwasher. I put 1 to 2 hours because I took my time and made sure all parts fit correctly and were back in their original place. Didn't want to take any chances in not covering bases. I am no expert, but definitely a diy'er. I believed I saved myself anywhere from $200 to $300 in labor costs by repairman. By the way, thanks Parts Select your info and site are awesome!!! The second part I had to order was the water inlet valve and your phone representative was a big help over the phone, please don't eliminate those positions. Overall total price of parts approximately $130 w/delivery. Well worth it, since a brand new halfway decent dishwasher starts at $550.

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.