JDB3000AWS3 Jenn-Air Dishwasher - Instructions

Unscrewed top of dishwasher pulled out wires from old control board and hooked up new one screwed dishwasher top back together, working great!

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Followed the repair video supplied by the site

I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Followed included instructions... worked like a charm!

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

I spent more time reading the easy instructions several times than it took me to actually do the repair to replace the fuse. I wanted to make sure I fully understood the instructions before I undertook the task. I also checked out a video on You-tube which explained and showed me the same thing as the instructions did. By the time I picked up the screwdriver, I was practically "an expert". I just cut two wires and hooked up two new wires and... done. The instructions were simple....so was the repair. Nothing to it.

I had to remove the baskets, spray assemblies (no tools needed) and disassemble the section of the pump that contained the chopper assembly. (removing three Torx screws)
I had to remove a part of the old chopper that had gone into the pump, but I was lucky that a magnet grabbed it so I didn't have to disassemble the pump.
The total repair was not difficult. The only problem was access (hands in the way while repairing difficult to see) and compressing the spring on the new chopper while trying to slip it into the groove.
The parts came in three days and they fit perfectly

Removed the old one, cleaned out the groove, dry fit the gasket, made a small cut to fit length, removed, squeezed the glue into the track and then put gasket in. Had to wait 24 hours for glue to cure.
No leaks.

Removed DW following great instructions for our unit at: repairclinic.
Problem when removing actual pump as a thin metal screen fell out after. Cleaned it and tried to reinstall the screen. It took over an hour figuring out how the screen went back in as it was cut to fit a certain way and had to try it over and over blindly then try to get it to stay before putting in pump. Finally put DW on its face. It was almost two hours after starting that everything was done exactly as instructed.

Started washer. Water came in perfectly. After about two minutes when the washer arms would start there was a horrible grinding sound and we promptly turned it off. My wife gave up the fight and is washing dishes by hand. That was a $172.00 experience.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

Partselect provided me with tracking information for my order, they also provided an installation video. So when I replaced the door seal it was a few minutes to remove the old seal and about five minutes to put in the new one and it was all done.Thanks to Parts select it was a piece a cake

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsSelect, and it was replaced in under 15 minutes without any tools.

removed front panel and pry switch from latch then remove two wires and reverse to install.