JDB3200AWS3 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Des Moines, IA
- Parts Used:
- 8269144A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Dish washer was very smelly.
After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from IRVINE, CA
- Parts Used:
- WP8565925
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Roller wheel broke off upper rack and also end rack stops needed replacing.
Husband watched your repair video. Everything went well and we are very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from MELBOURNE BCH, FL
- Parts Used:
- WP8565925
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
Top rack broke
I had to replace the whole sliding system on the top rack. Plus the clips holding it. It snapped. I watched the video and did the steps from Steve. The rack slides better than when brand new. Whirlpool wouldn’t pick up phone but part select did. So thank you for being there so I could fix the rack and be able to use the dishwasher again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from SICKLERVILLE, NJ
- Parts Used:
- 4317824
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent power loss
Remove power source, then remove old power cord.Run new power cord through existing opening ang attach to existing power box on bottom o f dishwasher. Install electrical leads and device ground. Reinstall cabinet bottom. Check out operation by running a cycle. All ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from LAKE GEORGE, NY
- Parts Used:
- WP8565925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
I needed to add a clip stop to the right front track.
I manually attached the track stop to the right track in the disheasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Prairie du Sac, WI
- Parts Used:
- W11196317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Water Leaking
Cleaned area, applied sealant and laid the sealant in. Unfortunately, it did not work. Still leaks. Going to the maytag store to get another and try again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Arlington, MA
- Parts Used:
- WP8565925
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Top rack of dishwasher kept pulling all the way out
Our dishwasher's top rack would pull too far out which made it hard to stay in alignment. It had lost it's track stop. I easily ordered the part from PartSelect, and it came more quickly than I expected; I clicked it in place and it runs like new. It's wonderful to deal with a company that knows the frustration of not having your appliance in good working orfer.
Thank you.
Sue M
Masdsachusetts
Thank you.
Sue M
Masdsachusetts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from tinley park, IL
- Parts Used:
- WPW10077871, 8193506
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
A leak in the bottom of the dishwasher
I turned off the power at the fusebox,then removed the front lower cover using a screwdriver. I then removed the complete assembly and reversed the procedure. Quite simple, and the info on Partselect saved me 85 bucks! I put Partselect in my "favorites" for future use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ana from scarsdale, NY
- Parts Used:
- W11196317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water was leaking from the door.
The first part we had ordered was incorrect. When we called the company, the person was very helpful, and understanding. The correct part was reordered and easily installed, after the old gasket was removed. The gasket area was cleaned and installation was as simple as the video. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from ST SIMONS IS, GA
- Parts Used:
- 8193983
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The 1/4" square part that the spinner at the top of the washer wore out and no longer supported the spinner. My dishes were not getting clean
Two philips head screws to get the arm reaching up to the oart removed. Snapped it in and I'm good to go! Clean dishes again! All for a 1/4" part.
Just followed the videi on this ste to make the repair.
Just followed the videi on this ste to make the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from LEVITTOWN, PA
- Parts Used:
- WP302868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lost Screws from lower access covers for my Dishwasher
Reassembled lower access covers using the new screws purchased from parts direct, perfect fit replacement. Hardest part remembering how they fit Dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Minnetrista, MN
- Parts Used:
- W11196317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
leaking water out door
Used new seal and glue. Your company was great. However, the part had changed and did not agree with the installation instructions. After calling the friendly person at your company to determine if I had the right part(it did not have a white stripe on it and did not look like the old part), I followed the instructions and it was easy. No leak-happy family.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from Ontario, CA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Drain pump had something lodged in it
In all honesty, it took me longer to remove the dishwasher than it did to install the new drain pump.
Pull the plug to kill the power, turn the water supply valve to off and disconnect the water supply hose.
Disconnect the drain hose and drain the water from it into a small tub.
Remove the two "anti-tilt" screws from the top of the D-washer
Remove the two screws holding the "toe kick" plate in place, remove the plate and place of to the side.
If needed, raise the front feet/legs, slide the D-washer out until you can reach the back legs, raise if needed, and side the washer the rest of the way out.
Lay out a towel on the floor, lay the washer on it back. You will see the discharge pump (the one with the big hose coming out of it), remove the hose clamp and hose from the pump.
Disconnect the little power plug from the pump
On the opposite side of the little plug is a gray little plastic tab, squeeze it and rotate the pump counterclockwise about an inch, the pump should fall out in your hand.
Take the new pump, rub a little dish soap (not that crappy hand cleaner stuff) on the rubber gasket and install the new pump making sure the little plug receptacle is facing you and rotate it until it stops, you should hear a small "click"
Now follow all the steps in reverse to put everything back together.
This site has a great, short video that covers everything I have mentioned above.
Pull the plug to kill the power, turn the water supply valve to off and disconnect the water supply hose.
Disconnect the drain hose and drain the water from it into a small tub.
Remove the two "anti-tilt" screws from the top of the D-washer
Remove the two screws holding the "toe kick" plate in place, remove the plate and place of to the side.
If needed, raise the front feet/legs, slide the D-washer out until you can reach the back legs, raise if needed, and side the washer the rest of the way out.
Lay out a towel on the floor, lay the washer on it back. You will see the discharge pump (the one with the big hose coming out of it), remove the hose clamp and hose from the pump.
Disconnect the little power plug from the pump
On the opposite side of the little plug is a gray little plastic tab, squeeze it and rotate the pump counterclockwise about an inch, the pump should fall out in your hand.
Take the new pump, rub a little dish soap (not that crappy hand cleaner stuff) on the rubber gasket and install the new pump making sure the little plug receptacle is facing you and rotate it until it stops, you should hear a small "click"
Now follow all the steps in reverse to put everything back together.
This site has a great, short video that covers everything I have mentioned above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerrie from GARDINER, MT
- Parts Used:
- WPW10404412
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Little plastic piece broke on door latch.
Disconnected power. Unscrewed inner door panel, unplugged and removed latch, put in new latch, plugged in, screwed panel back on, voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Duluth, GA
- Parts Used:
- WPW10348269
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher wasn't draining
The video does a great job explaining the repair. I took the unit completely away from the wall and put it on its side, which I recommend. Only problem I had was getting the new part in the correct orientation to lock... try to pay attention to how the failed pump is facing when you remove it.
I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.
I ended up replacing the supply line as well as just moving it around caused a drip leak, guess it was about to fail. Pro tip: don't remove the old line until you have the new line in hand... but that's a story for another day.
Was this instruction helpful to you?
Thank you for voting!