JDB6510AWK Jenn-Air Dishwasher - Instructions

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

The most difficult part is learning how to unsnap the plastic retainers at each end of the steel sliders on each side of the dish rack. Push the end caps to the outside and the plastic inserts will snap open and slide off the ends of the rails in two pieces (note how they were oriented so you can replace them later). The caps must be removed from both ends of each rail. Slide out the basket. slide the rails out. Pull the old rollers off the pins. Place the new rollers into position. A smart rap with the palm of your hand should snap the rollers onto the pins. If you have done it correctly, the rollers will not pull off the mounting pins. You could also place a small block of wood against the roller and use your hand or a small hammer or weight to snap the pins into place. Assemble in reverse order.

Unscrewed the dishwasher front panel. Took out the broken pieces of the handle and screwed in the new handle. Not hard at all. The website for the replacement part was easy to use & the part arrived quickly. Thanks

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

Turn off the power supply to the appliance. There is wiring you could mess up if something goes wrong. Open the door. Remove the four (4) torx head stainless steel screws on each side of the interior door panel. (total of 8). Then remove the two (2) torx head stainless steel screws near the top of the door on either side of the latch. Before you pry the interior door panel off, have handy a non-metallic weight, such as a brick or heavy book.. When you pull the interior door panel loose, the weight difference will cause the springs to pull the door up and closed. The brick will hold it open while you replace the cheap plastic handle. Do not try to fully removal the interior door panel as there are electrical wires attached. Just lien the interior door panel up onto the lower dish tray. You will need a 5/16" hex nut driver to remove the two (2) screws that hold the plastic handle on. Then, just reverse the whole process.

i removed the strainer cover and then removed the discharge assembly. then repeated steps to finish.. parts select was very fast and cheap ordered ontuesday and arrived on thursday. I will recomend parts select to all

I placed the distributer cap on and tightened with the housing nut and snapped the cap on and it was fixed. Very easy, no tools involved.

Removed the handle from the old basket and put it onto the new basket. The new basket is great!

Simply took old parts off and replaced them with new parts - no tools required.

Remove the old rack and slip in the new one. Took 5 min to figure out how to remove the upper rack. Now have "new" dishwasher. Great service by PartSelect.

I read the instructions given in one of your emails that said that to take off the center spray contraption, just turn to the right. To replace it on the new rack, put in place and turn to the left put the rack back in place in the dishwasher. It took less than 5 minutes after removing from the dishwasher.

Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.

Actually following the online video is the way to go.

My nephew actually put the new part back on for me. The main problem I had was getting both parts of the diverter ordered at the same time. I had to order the lid after the diverter came in the mail! I did not realize it was a two-part replacement piece. I learned later that the lid was a separate part.