JDB1105AWS44 Jenn-Air Dishwasher - Instructions

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

Shut off the electricity to the dishwasher. I removed all 11 screws from the door panel. After separating the 2 door panels, I removed the 2 door switches from the door handle ( I used a flat head screw driver to help get them out). Then I unplugged the 2 switches and plugged in the new ones. I replaced the door switches into the door handle ( this was not an exact fit because the new switches is slightly larger than the old ones). I put the new switches in place as tight as I could in the handle. I screwed the 2 screws holding the handle first to secure it before I put all the other screws in the door panel. I turned the electricity to the dishwasher back on. Our dishwasher has been working perfect ever since then and it is over 10 years old.

The actual problem was the plastic wash arm cap was worn down and not holding the spray arm in place allowing it to hit the lower dish rack and stopping it from turning. The cap is on a threaded steel stem and is easily removed. The spray arm lifts off the stem and its replacement slips right on. Then install the new wash arm cap by screwing it on the stem.

I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

Took a while to figure out what had to be done. Brackets have to go under the metal frame which involves dropping the compartment. That is done by removing the screws which are hidden under the door gasket. Once I knew what had to be done it was simple.

Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.

Ordered a new basket. Tossed out the old one. Done

Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.

I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!

The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.

The arm has a small bracket that can snap off and on the main water tube easily without tools.

Changing it was a snap!

After only 2 years, the Amana dishwasher door began to stick severely. If finally stuck so bad that I had to break the handle to get the door open. The replacement latch and handle fit perfectly and it only took a few minutes to get the screws off of the inner door panel to access the broken latch.