JDB1080AWS0 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stuart from Rockaway, NJ
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
rinse dispenser was clogged and unusable.
I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.
The new part arrived quickly and was the perfect match.
The new part arrived quickly and was the perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold L. from winamac, IN
- Parts Used:
- WPW10275768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle stopped engaging
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Lansing, MI
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
the dishwaster was not getting the dishes clean
The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Burlington, MA
- Parts Used:
- W10283681
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking do to heating element decay.
1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST NEWTON, PA
- Parts Used:
- WP99003446
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher door would fall open
I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from SAN FRANCISCO, CA
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Soap not dispensing
I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAKILA from FAIRFAX, VA
- Parts Used:
- WP99002598
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
one of the door spring broke
I bought 2 new new door springs and just replaced both left and right. Just have to pull out the dishwasher about 1/3 to its original position to be able to fully open the door and replace springs located on the side. This model is not complicated . Its very easy to replace parts that are broken. Don't forget to TURN OFF your CIRCUIT BREAKER
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Centreville, VA
- Parts Used:
- WP99003149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two broken lower rack wheels
It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Dix Hills, NY
- Parts Used:
- WP99002598
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The spring broke before the hook part on the spring.
Removed screws holding the dishwasher on the side of the cabinet.
Removed the screws from the bottom plate of the dishwasher.
Pulled out the Dishwasher from under the cabinet about 1 foot .
Removed broken Spring from left side of bottom holder making sure not to drop the plastic swivel arm from the bottom metal bracket.
Put the new spring, short loop side end in the plastic swivel arm and expand the long side spring end to the upper bracket holder. Their are 4 different tension slots depending upon how tight you want the front door to open or close. I put the spring on the 2nd slot
Put dishwasher back under the counter, screwed bottom plate & side in.
Removed the screws from the bottom plate of the dishwasher.
Pulled out the Dishwasher from under the cabinet about 1 foot .
Removed broken Spring from left side of bottom holder making sure not to drop the plastic swivel arm from the bottom metal bracket.
Put the new spring, short loop side end in the plastic swivel arm and expand the long side spring end to the upper bracket holder. Their are 4 different tension slots depending upon how tight you want the front door to open or close. I put the spring on the 2nd slot
Put dishwasher back under the counter, screwed bottom plate & side in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lake Zurich, IL
- Parts Used:
- WPW10192799
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dishes not clean
with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alain from Lake Mills, IA
- Parts Used:
- WP99002659
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
broken chopper
Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Longmont, CO
- Parts Used:
- WP99003317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Latch on soap dispenser door broke
I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Mapleton, UT
- Parts Used:
- WPW10192799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dishwasher got the dishes dirty not clean
My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nora from Wilmington, DE
- Parts Used:
- WP6-918873
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
bottom of silverware basket broke
received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eva from columbus, OH
- Parts Used:
- WPW10192799
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
accumulator filter
Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.
Was this instruction helpful to you?
Thank you for voting!