JDB1095AWS41 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Groff from WVisconsi Rapids, WI
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom of the old basket was breaking and silverware was getting stuck
Open the door and remove old basket. Place the new basket in its plave. Time elapse approximately 20 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from TWINSBURG, OH
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The silverware basket needed replacement since there were cuts in some places on the bottom which caused utensils to fall partway through.
Very simple. Just replaced the old one with the new one. Voila!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from NEWNAN, GA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket had holes in it from repeated use of holding sharp utensils.
Just replaced with new basket. Fit like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denis from JACKSONVILLE, NC
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out basket
Took old one out And placed new one in dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- betty from GEORGETOWN, TX
- Parts Used:
- WP6-918873
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Basket broke----bought a new one!
opened door---- took out old basket--threw it away. set new basket in its place!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Fort Myers, FL
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old basket seperated on the bottom.
Removed the handle from the old basket and put it onto the new basket. The new basket is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Ballwin, MO
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic in silverware basket cracked so utensils kept falling through/getting stuck
The basket did not include the handle (something I didn't notice when I ordered it). I simply removed the handle from the old basket and placed it on the new basket.
Having utensils falling through was really getting old. This was $25 well spent.
Having utensils falling through was really getting old. This was $25 well spent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Anaheim, CA
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Used Dishwasher In Our Condo Had No Silverware Basket.
Ordered silverware basket, placed into the proper position. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francine from Bristol, CT
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top wash arm kept falling off.
I had to remove the the old retainer from the old wash arm ,install it on the new arm by snapping it on then I snapped the arm with the retainer up top of dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Glenwood Springs, CO
- Parts Used:
- WP6-918873
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom of basket broken
take handle off old basket put on new basket done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Franklin, WI
- Parts Used:
- WP6-917644
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher arm keeps falling off.
I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.
The arm has a small bracket that can snap off and on the main water tube easily without tools.
Changing it was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Newington, CT
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken handle assembly.
Removed inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.
removed part.
disconnected switches.
plugged wires onto new part.
placed part in.
put inside cover on and screwed down.
Note: be careful of the bottom of the inside cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from NICOLLET, MN
- Parts Used:
- WPW10192799, WP6-917647
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Dishes not getting clean. Soap residue on dishes after wash.
After disassembling accumulator assembly looking for reasons that washer not washing properly, I noticed accumulator filter had failed. The plastic (or whatever material it is) covering the holes was torn in a couple of different holes. Realizing that this was not the reason for the loss of pressure I investigated a little more and found that water arm going into the docking station was extremely worn with much play. Water pressure was compromised because of it. I replaced filter and docking station and now its like a new dishwasher again. Saved a dishwasher from the landfill!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Greenville, PA
- Parts Used:
- WPW10275768
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Broken door Latch
Removed all the screws holding the inside panel of the door to the door itself. Lifted out the old broken door latch. Pulled the wire clips from the 2 switches located on either side if the door Latch assembly. This is a bit difficult. You have to keep working the wire clips back & forth; Up & down until the clips are free from the switch metal contacts. Reinstall the wire clips on the new door Latch assembly making sure you attach the black wires and white wires on the same side of the new latch assembly as on the one removed. Replace the new latch assembly aligning the mounting holes on the door with the new latch holes. Replace the inside panel aligning the holes and replace the screws. The screws were the star head type so you need a special driver bit. I used the box the latch came in the prop up the inside door panel while I worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PORT JEFF STA, NY
- Parts Used:
- W11082871
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water inlet valve had to be replaced.
I pulled out the dishwasher enough to tip it back and put a block of wood underneath the front leveling foot.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
This step gave me more room to work on the valve.
I removed the lower cover plates to expose the valve.
I disconnected the incoming water line and unplugged the electrical connection.
I then unscrewed the bracket to release the valve from the case and took off the rubber hose attached to it.
I installed the rubber hose on the new unit and installed the bracket back in place. I then wrapped some Teflon tape on the threads of the valve fitting and re-installed the water supply line. I re-installed the electrical connection.
I then turned on the water to check for leaks. Once I was certain there were no leaks, I re-installed the lower cover plates and took out the wood block and pushed the dishwasher back into place and re-installed the screws that held it in place.
I then ran a load of dishes to make sure everything was working properly.
Was this instruction helpful to you?
Thank you for voting!