JDB1080AWW Jenn-Air Dishwasher - Instructions

I simply snapped the new wheel assemblies back on. The main thing I want to say is that I have never owned a dishwasher that required replacing wheels and I believe there is a design flaw in the wheel that they break so easily. If you look at the way they are mounted on the rack, eventually the weight of dishes on the rack will wear them out and break them. It cost me nearly $50 to replace them all. I bought extras because I know more will break in the future.

First I removed the Torx screws holding on the door cover (two of these screws also hold the latch assembly). You don't need to completely remove the cover but just keep it slightly separated by hand as you do the work. I attempted to remove the connections to the two switches on the latch assembly but this proved to be very difficult even after applying lubricant so I changed my approach. Since only the latch handle was broken I decided to remove the two switches from the existing latch assembly and attach them to the new latch assembly rather than disconnecting the wiring harness. There are two clips holding each of the switches and by pulling them back you can remove the switch. After this was done I was ready to put in the new latch assembly. I removed the two switches off the new latch assembly and have kept them in case a switch happens to fail in the future. I placed the new latch assembly into the dishwasher door and then pushed the wiring harness (with the old switches attached) into the new latch assembly. Take note that there is a "detent" in the switch that must be pushed in as you slide the switch into place or otherwise it won't seat properly. After putting the two switches back in place I closed the cover and tightened the two screws that hold the latch assembly first and then tightened the remainder of the screws. It took a full 30 minutes but that included changing my approach after the harness wouldn't separate easily from the switches.

I used to love my dishwasher, but the top shelf was hanging and the bottom rack kept getting hung up. I was helping clean up at a friends house and was very envious of how nice her dishwasher was working. I was considering getting a new one. Then I decided to go online and see if I could find the parts. For under $15.00 I purchased both wheel assemblies. Also, I received them the next day!! Now, I love my dishwasher again....

The repair stories on PartSelect.com told me exactly what to do.

First, I checked the inside of the door and confirmed that the inside panel of the door was held in place with about 10 torx screws.

Second, I went out and bought a set of torx screwdrivers.

Third, I TURNED OFF THE POWER TO THE DISHWASHER AT THE BREAKER BOX! Safety first!

Fourth, I removed the screws and gently lifted the inside panel of the door, and then gently lifted the broken door latch assembly out of its slot. (There were no more screws to remove, because the latch assembly is held in place by two of the door screws.) Two sets of wires, one white and the other black, were connected to the latch assembly by plug-in connectors.

Fifth, I unplugged the wires from the broken latch assembly. The clips in the plug were very tight, so I used a dishtowel to hold onto the latch assembly. I found that gave me a better grip.

Sixth, I plugged the wires onto the new latch assembly, and then slipped the latch assembly back into the slot.

Seventh, I replaced the inside door panel, and replaced in the 10 torx screws.

Finally, I turned on the power at the breaker box, closed the door, and turned on the dishwasher. It ran perfectly!

I would like tyo add that I had ordered an unnecessary part by mistake. I called the return number, and the person who answered was extremely helpful. She gave me the return authorization number and I put the part in the mail. Ten days later, I received an email from PartSelect.com confirming that the part had arrived and that my account had been credited.

The entire process was easy and pleasant. Anybody can do this! Just make sure to shut off the power at the breaker box before you start on the job.

The web site was great in finding the part that was required. Once the parts was received ( it took four days to et the part ths was very fast) it took only 30 mins. to complete the repair. I had to remove all the screw on the door, lift up the inside door cover and remove the handle latch assembly. I removed the two mico switches from the old handle and installed them into the new handle. I replaced the new assembly and replaced the inside door cover and replaced the screws. This was a very easy repair.
I had called a local repair shop to see what it would cost to repait the dishwasher. They told me that it would cost $60.00 to come to the house to see what was wrong with the unit. Next they would charge $75 per hour (minimum of $75 if it was less than one hour of repair time) for the repair plus the parts. THis repair cost me less than $30 plus 30 minutes of my time. Great savings

First I removed the lower spray arm by removing the middle retainer nut. Next remove the 3 screws holding the outer shroud in place. Next remove 6 screws holding the water pump top housing in place. Under this housing you will find the impeller which is retained by a screw. Check the impeller closely for cracks especially near the center hex portion of the impeller. Replace if you have any doubt of it's integrity. Next remove the lower pump housing that has the screen material in the center. What I found was the nylon part that attaches to the shaft of the motor was stripped so the impeller would spin in it's normal direction ( counterclockwise) but under the load of water it would not. So I ordered a new impeller and seal kit with a metal sleeve and chooper blade. Follow the instructions provided in the new kit a reassemble accordingly.

I had to remove the 4 screws holding the toe panel. Then I had to take out the one screw holding the floater switch housing in place. It snapped open to release the floater and that just lifted out. I put the new float in and snapped the new housing on. I put the screw back in to hold the housing in place attached the two wires to the switch and put the toe panel back on. It was all very easy to do and my first home repair went very well. thank you.

I went to PartSelect and found the parts pictorial. A replacement motor was listed for 3 series of the dishwasher. The series can be identified by the first 2 digits of the dishwasher serial number. Mine was 22 so I needed parts for the series 20 dishwasher.

According to the pictorial it looked like the motor seals were included with the replacement motor. When the motor arrived, I found the seals were not included. I called PartSelect and they shipped the seals to me with free overnight delivery.

I had no trouble disassembling the wash manifold and spray parts using the instructions provided with the replacement motor and the instructions from the Maytag repair manual that I found online. The motor is removed from the inside of the tub.... very nice. You don't need to remove the dishwasher from under the counter in order to get at the motor.

I made a mental note of the orientation of the faulty motor before I removed it. I installed the replacement motor with the same orientation along with the wash parts. The dishwasher worked successfully.

Thank you PartSelect.

After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

the new dishrack fit right in immediately with no tools needed. Delivery was prompt

I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.

I removed the 11 screws that hold the plastic inner liner to the outer sheet metal of the door. The latch will be right there, and very easy to access. I Just removed the two connectors for the wires, which are a bit stubborn, and used a pliers for leverage to get them off the latch. Installed them on the new latch, and put the door halves back together, and ran the 11 screws back in. A side note, I have noticed that on the plastic front panel that houses the buttons, that there are two plastic tabs that are cast into the unit, that are chronically broken. They are there to help hold the latch solid when you put the two halves of the door together. I have been really easy on the door, but they still break, but it seems to work pretty well without the tabs intact. This happened to me twice, because I replaced the front upper panel on it, and the same thing happened again. Engineering issue I assume. Overall, a quick and simple install.

We ordered a Control Panel first (not sure what part we really needed to fix the problem). After installation and the Control Panel didn't solve the problem, we knew we needed the Circuit Board. We then ordered the Circuit Board and upon receipt itstalled it. The Circuit Board was simple to install and BINGO! It worked perfectly. Thank you for have the parts we needed.

Reynold Burbank

Removed plastic lining from dishwasher door with torx screwdriver, then removed screw holding door latch assembly in place. Removed existing switch from door latch assembly and replaced.

This switch was not the correct one initially as it was a normally closed switch, whereas the existing switch was a normally open. Was able to pry open the switch and switch the contacts to normally open so it worked out in the end. Would recommend purchasing the complete latch assembly w/ switches if you aren't comfortable taking the switch apart.

Looks like Maytag knew this was a problem. My chopper sleeve (plastic) was stripped and causing the impeller to not spin. The replacement part was all metal and was very easy to replace the old one just by removing screws. The replacement looks to be very sturdy and should last a lot longer than the original. Thanks.