JDB7910AWB Jenn-Air Dishwasher - Instructions

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

i removed the strainer cover and then removed the discharge assembly. then repeated steps to finish.. parts select was very fast and cheap ordered ontuesday and arrived on thursday. I will recomend parts select to all

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

Purchased a replacement lower rack WPL 99002572 (which had the wheels but not sure that it still does.) Used the old fold down shelf but this might be available as a part. The rack didn't have the tines near the rear of the rack on either side--my old one had fixed/welded tines so I didn't expect this and needed replacement parts to fix it. I Ordered 4 straight clips AP4112831 (99001436)CLIP, FOLD AWAY TINE to hold the tines. There weren't any recommended tines, so found and Ordered 2 each Front place and Rear Bowl tines WPL 12002218 x 2 and WPL 99002138 x 2 that looked about the right length. Used them in pairs. On one side of the rack (right side), only the bowl configuration works--this is because the tines catch on the edge of the basket and won't fold straight up. On the other side (left), I can switch between bowl or straight tines by folding them different ways. To make this work,clip the tines to the basket so the tines set a little closer to the center of the basket than you might expect, in order to allow the tines to 'float' enough to rotate to the opposite configuration. I had to experiment with the clip location so needed a needle nose pliers to gently unlatch the clips so that I didn't break them. I also ordered a clip AP4113042 (99001746)Latch, pivoting tines--but didn't use them with these bowl tines. They might be useful with a straight tine for latching the top to the outside of the basket.

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

Had to disassemble the door, using a Torx 20 driver to remove about 10 screws. Then pulled the door apart and used a 1/4" nut driver to remove two screws. Replaced the handle, reassembled the door and all worked normally! Easy repair for anyone with the confidence to take apart the door.

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

I pulled the unit out its bay and saw that one spring was missing. I looked up the parts online and ordered replacement springs and linkages. Using the existing spring and linkage as models, I easily installed the new parts. I ordered spare parts in case the other linkage broke.

Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.

When I tried to remove the hold down screw for the impellar, the impellar broke in half. I actually did npt need to go this far with disassembly as the problem was with water being retained in the rinse arm assembly and stagnating. This was due to calcium buildup clogging the drain holes. Clearing the holes resolved the problem.

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel

Changing the valve only took about 30 minutes but reusing the fitting from the old valve I could not get it to stop leaking on the copper side of the fitting. I ended up going out and getting a new fitting and cutting the copper line to make a new connection. Then the problem was solved.