DP471 Jenn-Air Dishwasher - Instructions

Replaced whole assembly

I removed four philips screws to remove the front door panel. Next I removed the screws holding in the detergent cup. Removed the two electrical wires from the cup release. Reveresed the process to install the new detergent cup.

Removed the seal and replaced with new one. Job went very easy. Stop the leake. Thank you.

Claude Miller

Removed the back - Saw the broken clips on the base of the dryer (the wires to the motor were pulling out because the motor was slipping).

Guessed that the parts were motor clips (no pix in the web site!)

Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!

(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)

After removing the cover to the motor assembly, I determined that the problem was that the old drive belt had broken. It probably was more than 20 years old. I originally thought that the size was no longer available because the old belt had stretched about two inches, but, after reading the repair stories on the PartsSelect Website, I decided to try the 25 3/8" belt. It worked great! After a few tries I was able to stretch the belt across the two pulleys without having to loosen anything. After applying the silicon grease, the dishwasher worked as good as new. The most difficult aspect of the job was having to work in such a small space. The most time-consuming part of the job was removing and then replacing the access cover, but the job overall was quite easy.

removed retaining nut and replaced

Read thru the comments by others and matched them up with what I found (belt off the pulleys) when I took off the kickplate below the door. The old belt (20 years) had stretched about 1 1/2" compaired to the new replacement. Slip the new belt on the motor pulley and start it around the back of the pump pulley. Get your wife to hold your legs down so you can really twist/pull the pump pulley until the belt finally slips into place. No need to loosen the motor mounts if your wife can hold you down.

First removed the four screws to the lower front outside panel (the only tools needed to complete this job). Slide the belt under the drive motor, onto the motor pulley grove, then strecthed the belt onto the pulley for the pump that's on the power module (was qiite difficult, but with the directions supplied with the belt, was able to get it on) Lubricated the belt with silicon grease.

First of all, ordering the parts from PartsSelect.com was very easy to do, I found and paid for the part in about 10 minutes with only the model number.

Removed the screws holding the old flange. Pulled it out and put the new one in its place. Installed the screws.

After I was finished I looked at the instructions. I'm glad I didn't look at them prior to starting. They were actually confusing.

I removed the access panel and it was right there. one screw - disconect the wires & it was out. then right back in - access panel on, and done.

I removed the 4 lower Phillips head screws on the lower inside of the door.(thanks to a tip from Robert) This removed the front panel allowing access to the detergent cup. I removed the 6 screws holding the detergent cup. Removed the old detergent cup and gasket. Installed the new cup and gasket and reinstalled the front panel. Amazingly easy. Now it's on to my stove. I'm hooked on your website

Removed the kick plates to access the pulley system, Heated the clear belt in hot water and installed it by rotating the large pulley to stretch the belt on. Then added the lubricant to the belt. Reinstalled the kick plates with nut driver.

After discovering the broken belt. 2 Days later I had the new belt from partselect. I placed the belt on the motor pulley then after 3-4 attempts was able to get the belt on the other pulley. It will go on. Comments from other customers really helped. After you get belt on then apply lub, per instructions. My maytag is over 20 years old still works great.

Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.

replaced gasket.Didn't fix leaking water problem.I believed that there was too much water in washer, when the problem occurred.Found that the float had soap build up in it making it too heavy,letting in more water than the washer can handle.Cleaned build up from float and problem seems to have disappeared.