DP471 Jenn-Air Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Margaret from Westampton, NJ
- Parts Used:
- WP901403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door gasket was leaking.
My daughter and son removed the old gasket and installed the new one. It went well.
Was this instruction helpful to you?
Thank you for voting!
upper spray arm nut was broken
found the parts ordered them an poof dishwasher us as good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from union, NJ
- Parts Used:
- 901839
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Detergent dispenser would not always dispense detergent
It was either the timer assembly of the Dispenser cup assembly. After looking at the dispenser critically< it appeared that the cam was quite worn. The replacement was accomplished by removing the bottom part of the door (4 screws) and then removing the dispenser cup (8 hex-head screws). If you keep the starter lever to "off" there is not power to the timer and you do not need to disconnect power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Cement City, MI
- Parts Used:
- 901839
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Soap door wouldn't open.
Removed four screws that hold front panel. Disconnected two wires, removed six screws, cleaned of old gasket material. Installed new gasket and soap dispenser with six screws. replaced two wires. replace front panel.
Was this instruction helpful to you?
Thank you for voting!
Detergent cup would not dispense/open
It is realatively simple to replace the dispenser cup. Revove the 4 screws on the inside edge of the door (Not the upper screws for the upper
control panel). The front cover will come away exposing the dispenser cup. Using a 1/4 nut driver
remove the 6 (I think) screws after unplugging the electrical connector. (Be sure & replace in the same position.) After removing the screws, the unit will easily come away. Clean the old gasket remnants & crud well and place the new gasket and cup in line with the nut holes.
control panel). The front cover will come away exposing the dispenser cup. Using a 1/4 nut driver
remove the 6 (I think) screws after unplugging the electrical connector. (Be sure & replace in the same position.) After removing the screws, the unit will easily come away. Clean the old gasket remnants & crud well and place the new gasket and cup in line with the nut holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Cupertino, CA
- Parts Used:
- 6-9021150
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
belt on old maytag dishwasher broke
removed screws that secured cover plates. discovered that belt was broken. ordered new belt. ordered friday; delivered monday. read some previous repair experiences.
the trick to getting belt onto the pulleys is to first wrap it around the spindle part. then set the belt into the motor pulley groove. carefully start working the belt in the other pulley into the groove while rotating both pulleys. i had to lay on my stomach on the floor to do this, but it did not take very long. once the belt is in place, lubricate it with the included gel. took about 20 minutes with some trial and error.
the trick to getting belt onto the pulleys is to first wrap it around the spindle part. then set the belt into the motor pulley groove. carefully start working the belt in the other pulley into the groove while rotating both pulleys. i had to lay on my stomach on the floor to do this, but it did not take very long. once the belt is in place, lubricate it with the included gel. took about 20 minutes with some trial and error.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from elk grove, IL
- Parts Used:
- 6-9021150
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
belt broke
replaced belt....great service!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Woodbridge, VA
- Parts Used:
- 901839
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Soap Dispenser did not always open due to leak around the stem
Removed front panel by removing four screws. Used 5/16 nut driver to remove six screws holding dispenser and disconnected two wires. Inserted new dispenser and reattached cover. Longest time taken was to realign cover properly. Best approach seemed to install with door as near vertical as possible and to start screws by hand. ONLY FOUR screws hold the panel in place. Very easy repair for anyone. part arrived sooner than expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Forty Fort, PA
- Parts Used:
- 6-9021150
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable), Wrench set
Broken belt
This was a pain to change due to very limited access. Also belt had very little stretch. Had to really put some thought in it before attempting.
Was this instruction helpful to you?
Thank you for voting!
soap cup would not open for second wash cycle
bimetallic latch to release soap cover was broken.
Had to order entire soap cup assembly to get the bimetallic strip. Removed strip from new assembly and replaced broken strip. Put remainder of cup in box and saved for spare parts.
Had to order entire soap cup assembly to get the bimetallic strip. Removed strip from new assembly and replaced broken strip. Put remainder of cup in box and saved for spare parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from SANTA ROSA, CA
- Parts Used:
- W10841140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
leaking front door. loose seal.
Followed instructions, those were OK.
Dishwasher front still leaking
Dishwasher front still leaking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Edina, MN
- Parts Used:
- 6-9021150
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
replaced broken belt
lostened motor mounts,
streched belt across pulleys,
thghtened motor tension
replaced access panel.
streched belt across pulleys,
thghtened motor tension
replaced access panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J.T. from Natchez, MS
- Parts Used:
- WP99002560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the washer got to where it would run and stop and repete
had to remove the iner door plate and remove the main switch or latch to get to the micro switches witch one had over heated over time,it is working like new at this time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irit from Valley Village, CA
- Parts Used:
- 900796
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The nozzle breaks every few months
it was very easy to unscrew the broken nozzle and screw back the new one. !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shayne from Andover, KS
- Parts Used:
- 901839
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Detergent cup wouldn't open during wash cycle
Firstly, I'm a 58 year old female and this repair was relatively easy for me, thanks to all the marvelous instructions on this site from others who made this same repair. Like the others, I removed the four lower screws on the INSIDE of the door along either outer edge. Before that, in error, I removed the four screws along the very bottom of the door, big mistake, hard to get them back in correctly. Removed the door panel and took out the 6 nuts from the dispenser cup, slipped the electrical clip thingys from the posts by slightly wiggling them straigt off, remember which color goes where. Cleaned the area around the old gasket and reattached the new gasket and dispenser cup. This was a little tricky holding it in place from the inside while using the nut drive on the outside. Whew! That was the hardest part for me. Thanks to all for the previous detailed instructions. I now have really clean dishes! Yay! Great feeling of accomplishment.
Was this instruction helpful to you?
Thank you for voting!