DW860UQW Jenn-Air Dishwasher - Instructions

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

Pulled out the old gasket and pressed in the new one. No more leakage.

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

My son was able to take the inside panel off to access area for handle to be replaced. A removal of approximately 12 screws and a little glue to glue felt pads in place VIOLA all fixed! Love this dishwasher so quiet and not ready to give it up.

removed lower dish basket. then removed 3 screws lifted element cover and removed center hold down nut lifted spray nozzle nad installed new parts. dishwasher is working like new.
thanks for asking.

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

Assumed that the door gasket needed replacing so I went to Partselect.com. Ordereed the gasket and was about to check out when I noticed the comments from others. Decided to look and was glad I did! Almost everyone said that the gasket on the soap dipenser latch on their door gasket repair was bad also so I ordered the latch gasket too. Parts arrived in only two days. I was amazed.
I started by turning the power off at the panel box, then removing the door gasket and cleaning the gasket groove. Then it was a simple matter of pushing the gasket into place, avoiding stretching or compressing it. Removing the gasket and putting in the new one was only about 3 minutes work - however cleaning the groove took somewhat longer. Then unscrewed the 7 torex screws on the interior door plastic panel. Carefully work the panel free, study the solenoid to see how it pops out and it attached, remove the solenoid and the panel is free of the door.
Examine the interior workings of the soap dispenser to see how it all fits. The remove the two hex head screws with a nut driver and carefully remove the assembly. Notice how the latch gasket fits with its boot in the notch on the latch base. The old boot was completely torn from the gasket base on mine. I cleaned accumulation of soad and crud from the mechanism and from the interior side of the door panel. Put it all back together in reverse order. The cleaning took longer thna the actual repairs.
Thank goodness for the comments - saved me a ton of aggravation!!! Partselect.com rules!

They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.

I took off the pump cover, removed the broken part. The support was broken at the threaded area so I needed to remove both pieces. Then I just used the diagram to see how all the pieces fit back together. I always take a picture too just in case I don't remember how it should go back.

Super easy repair.

I removed the inside panel. This exposed the rear of the control panel. I carefully replaced the defective switch. Only one was bad but of course i replaced both.

From other comments on this site, I learned that 2 people fixed the problem with a new door gasket; 3 fixed the problem by replacing the dispenser latch. I tried the gasket and it helped some (obviously needed replacement anyway) but then learned that the rubber boot around the soap dispenser latch was torn into two pieces. Replaced it and good-to-go.

Used your web site was able to identify correct part very quickly. Received the replacement part in 2 days.
Removed broken part with screw gun only took 20 minutes. Was very please with ease of site and quick delivery.
Thank you

In front of the dishwasher, my wife and I noticed pooling water when the cycle was running. I was fearing the worst, that the tub was leaking from underneath, or that the supply system was leaking and I was going to have to take the whole sucker out. Not so.

I saw that the door gasket was very hard and corroded from our local hard water. I got to this site and saw that others replaced the dispenser door latch grommet, too, and four bucks was a reasonable add-on to make sure the whole thing was dry later.

The door gasket itself was about a five minute repair. No real tools required, except that a blunt pushing tool is helpful. The only trick was making sure that both sides were relatively equal on the bottom.

The dispenser door latch thingy was a bit more complicated. The driver set I was using fortunately had a Torx bit that fit the plastic door panel screws. I then tried dissembling the door solenoid/release mechanism, but I should have just undone the nuts and taken the whole thing off without taking the small pieces apart. Anyway, I replaced the grommet easily and then got all the small stuff put back together OK.

This was an easy repair without pictures or instructions.

I removed the four screws that hold the front kick plates on. Then, I removed the hose clamp (on the right side of the pump that secures the top shower hose assembly to the pump assembly. Then I pulled the dishwasher out, and pulled out the four black snap clips that hold the insulation in place. I then folded the insulation back and reached inside the dishwasher to disconnect the hose assembly. On the top spray arm is a nut that is easily removed without any special tools.
Be sure to save the rubber washer unless you order a new one along with the top shower hose.
Overall, an easy fix. Saved about $100.00 by doing it myself.