DW860UQW Jenn-Air Dishwasher - Instructions

1. Turned power to the unit off.
2. Used a star bit to remove the 7 screws holding the door panel in place.
3. Handed each to my 2 year-old grand daughter.
4. Removed a 1" switch metal retaining plate and a black plastic cover. Removed one screw holding the switch in place.
5. Gently lifted out the old switch and compared it to the replacement switch.
6. Inserted the two black connectors into the new switch.
7. Removed each of the four wires connected to the old switch and connected each, in-turn, to the new switch. Removed the exterior black handle from the old switch and snapped it into place on the new switch.
8. Put the switch into place, reinstalled the black plastic housing cover and long 1" metal switch retaining panel.
9. Set the door cover in place and let the 2 year-old screw in the 7 retaining screws.
10. Don't have to listen to the wife complain about the dishwasher anymore.

First, removed end cap in steel sliding upper rail, second, removed broken roller, third, attached new roller, you can look at other rollers to see how it goes on, fourth, feed new roller into track, replace end cap. Takes less than 10 min, saved 85. 00 Bucks.

Took off old part. Modified new roller w'knife. Found a nut and bolt in scrap pile. Attached.

I first turned off the water to the dishwasher, then the electricity to it, then took off the front bottom access panel, I then unbolted the inlet valve from the side of the machine, undid the electrical hookups remembering which one connected to which, then unclamped the two hoses, I then put the new one back in place, redoing the hoses and electrical and bolting it back to the side of the machine, then putting the front bottom access panel back on, then turning back on the water and electicity. The one thing that may make it easier if you can is to pull the dishwasher out from under the cabinets and lay it down so the bottom is exposed. This would make the process a little smoother.

First, I removed the foot plate(s) at the bottom of the Dishwasher. (2 screws each side)

Then I removed the two top screws at the front of the dish-washer. The screws were mounted into a board under the counter that had broken loose. (A minor secondary issue specific to my situation.)

I gently inched the dishwasher out from under the cabinets.

SLOWLY, I tipped the dishwasher over on its side, allowing the water still inside to drain into a pan. Minor cleanup required for the cup or two that missed.

I then had access to the part. I disconnected the power from the wall socket, and I closed the valve for the inlet water from under the sink.

I removed the screws holding the Water Valve to the DishWasher case. Then I took a sharpie and marked one side of one of the two power connectors, black-mark to black-mark.

When I went to disconnect the inlet pipe, there was more dripping than I expected, so the valve under the sink was not closing completely. I needed to shut off the water supply to the house for the next stage.

I disconnected the inlet water supply, which continued to drip slightly into a bucket. I then removed the coupler from the old water valve. It was badly clogged and corroded, so I went to a local HW store and found an exact match 3/8" to 3/8" right angle coupler with compression fitting on one end.

BIG TRICK, before installing the new coupler, WRAP the compression fitting threads with teflon tape. You will not be able to wrap it once it is installed. In fact, I needed to uninstall the part once after I discovered this, to wrap the threads smoothly.

Once pre-wrapped, wrap the other threads that screw into the water valve. Tighten until secure, AND aligned with the direction of the flow tubes of the original.

Match the electrical connectors, black-mark to the same position as before. (The new water valve will NOT have the black-mark on it, unless you transfer one!)

Connect the Water valve back to the Dish Washer chassis with the two screws previously removed.

Connect the inlet water back to the compression fitting with the pre-wrapped threads.

Gently return the dishwasher to upright, and then plug it in.

Open the valve under the sink slowly and watch for drips or leaks.

Run the dishwasher at the start of a cycle, long enough to determine that the valve activates, and allows water to flow. Then stop the cycle.

Gently walk the dishwasher back under the counter, observing that you do not kink the copper water inlet pipe, or the drain pipe.

Adjust the feet, if necessary, back to fully support and level the dishwasher.

Install the two screws holding the dishwasher to the cabinet front. Then install the kick plates and tighten those 4 screws.

Clean up any residual water from the process.

The wax motor seemed to work.
At first I thought something was broken and I tried to figure out the "theory of operation" Working the actuator of the wax motor, I COULD NOT GE THE LATCH TO MOVE THE WAY I THOUGHT IT SHOULD. I ASSUMED EITHER IT WAS BROKEN IN SOME WAY I COULD NOT DETECT OR THERE WAS A FLAW IN ITS DESIGN!

It took a long time to figure out the latch would not be worked open unless it was actually holding the lid- this positions the latch at "half mast" and allows the mechanism to "pick it up from there" and open the rest of the way. So once I figured that out, I concluded the failure was really just worn out parts that were out of tolerance for how this "half mast" position and opening was supposed to work. So I ordered all fresh pieces just to be sure, assembled it (very easy) and put it in (easy). It all works fine now.

First I called a repairman. He saw it was a certain model Maytag and would not fix it. It washed, but would not drain, so rather than buy another I took about an hour to carefully remove the washer and the motor / bowl unit from the body. Then it was easy to see what was wrong. The problem was a broken lifter arm in the bottom of the bowl. This caused the drain solenoid piston to "travel" too far and actually dislodge from the solenoid during use. You have to remove the lower spray arm, drain grate and then the lifter is a little black plastic "arm" on a metal rod that is actuated by the solenoid under the washer. The lifter fits over the rod and is held with a snap ring. Re-assembly was easy.

Whoever manufactures this part, hope they read this and strenthen this part. The very thin legs break very easily.

I removed the threaded broken-off part from the extension thing. The spay arm came off, since nothing was holding it on any more. I pried the cover off below that - 4 tangs.
Then I used needle nose pliers to unto the strange pointed nut that holds the spray arm support in place. Then removed the borken support, replaced with the new and reassembled in the reverse order of disassembly. Really pretty easy.

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

After performing some maintenance to get the water flowing properly through the system (that's another story) the door was leaking very badly during any test run of the dishwasher.

We thought it was the gasket because the old one was calcified and dried out from years of harder water.

We ordered the new one and in minutes after receiving the new gasket we had a firm seal and our dishwasher was back in action.

I removed the screws on the inside of the door. Removed the cover and changed door switch and holder and put the new one in. Replaced the cover
all in less than half an hour.

1 - Turned off the power
2 - Loosened screws on inside door panel
3 - Removed panel (still attached by ground wire)
4 - Removed black swtich cover
5 - Removed screws holding latch assembly
6 - Dropped in new latch
7 - Pulled away plastic switch holder, carefully
8 - Examined black micro switches (Land R); noticed right switch button defective
9 - Removed wires (2) from clips on right switch
10 - Pulled out switch (holding up plastic arm)
11 - Replaced defective switch from those in dorr switch assembly (I did not replace the plastic assembly itself, since the old one was OK, but you could if you wanted to be punctilious about it.
12 - Screwed assembly back in position
13 - Put on black cover again
14 - put on inner plastic door panel
15 - Screwed panel back
16 - Ran a load of dishes - perfect!

The dishwasher is well engineered to perform this work.

Remove the bottom two panels to provide access and visibility to base of pump motor.

Locate plastic pump locking lever and push toward rear of DW to unlock pump from DW.

Inside the DW remove basketsand spray arms. Revove screws holding cover over pump motor and remove cover.

From below raise pump motor and support with block (piece of 2x4 worked well).

insde DW, removre old gasket, clean well around pump and botom of DW, install new gasket.

From below remove block to drop pump motro back into place, and re-tighten locking lever by pull toward you.

re-assemble inside componets, run through a rinse cycle to test for leaks and replace bottom panels.




I

I was able to remove the old handle and place it on the new basket - using only a screw driver.

had to remove the spray nozle and cover from the bottom of the washer to expose the stem where the lifter mounts. I had to turn the stem slightly to install it, this had to be done from the bottom of the washer and it took an extra set of hands. Once the stem was in the right position the lifter slid right on, I attached the retainer ring and put the othe parts back on. It works as good as new now.