DW760W Jenn-Air Dishwasher - Instructions

I replaced the door latch grommet just as everyone else has described on this site. It was pretty easy. I was amazed that such a little piece of rubber can let so much water get by. The inlet valve was not too bad either. Take the two bolts out that hold the bracket to the dishwasher. Remove the rubber hose on the back side and take loose the two electrical connections. My water line was long enough to pull it out in front of the dishwasher. Then I took the water line loose and removed the fitting. Installed the new one in reverse order of what I just described. These items took care of the bulk of the leaking problem. But I am in the process of ordering a new door seal which I hope resolves the rest of the issue. Also make sure you check the upper and lower control arms to make sure the spray holes are free of debris. This dishwasher was full of pieces of clear plastic that caused the spray arms to spray indirectly and towards the cracks of the doors.

Sooooooooo, I ordered a new kick plate, it arrived promptly, tried installing it and it was being difficult. Removed plate above that and lined up new plate(kick plate) tried putting plate above it on and as when we installed the machine that upper plate was difficult. Removed upper plate to fcheck problem of installation and guess what? Stuck in the inside of the upper plate was the lower plate complete with sound insulation. Happy ending :-)

Once I pulled the old broken drain valve lever lifter off the shaft, the shaft rotated counter clockwise. I then had to turn shaft back clockwise so there was enough room to slip the new part on. Needle nose pliers worked great to hold it in place while regular pliers in the other hand was used to turn the shaft.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.

This is the second time I've purchased parts from PartSelect.com. Actually called Lowe's parts hotline and got disconnected three times. Went online with PartSelect.com and purchased the items within 5 minutes. Parts arrived within 2 days. Will definitely be purchasing parts from PartSelect.com again when needed!!!

Myscanning other reviews i saw mention dishwahser developed a small leak on RHS of door. I assumed the door gasket and planned to order that. On of the dispenser gromet which is only a $5 part so ordered that as well. I first replaced the door gasket which is an easy 10 mins job and ran the dishwasher again, but it still leaked.

I then removed the 7 torx screws on the door panel which came away easily. It was obvious that water was in there, so i removed the two screw on the dispenser with a nutdriver to replace the grommet. This process took 20-30 mins. After reassembly the leak was gone.

Without the comments on the website i would never have thought of the disepenser as source of the problem.

I used a torx driver to remove the seven screws holding the inside door panel in place. Flipping it over exposed the dispenser mechanism. There were two hex nut screws holding the whole assembly in place and two wires attached to the wax motor. As an afterthought I had ordered the sealing grommet for the latch, and as it turned out, the main problem with the sticking latch was that the grommet had worn out and allowed the hard soapy water to leak into the slider assembly and build up a hard crusty residue that had helped to ware out the old wax motor. After completely disassembling all of the parts, I scrubbed the residue out of the housing, replaced the slider, latch, spring, and grommet. Next I snapped the new wax motor into place and connected the two wires. The whole thing went back in place and the two hex screws went back to hold it all together. Finally, the seven torx screws went back to put the door back together. The whole repair went without a hitch.

I used the parts blowup diagram on PartSelect.com and dissasembled the bottom wash assembly. Carefully examining how the washer arm rotated, I determined that the spray arm support nut had broken. The extended top of it has broken off. This nut, when tightened, allows the spray arm to rotate freely. In trying to diagnose the problem, I had even removed the motor assembly at the very bottom. When I reassembled it, I apparently did not seat the gasket well and did not tighten the bolts well, so when I tested the washer, water leaked out the bottom. So, I had to dissasemble it all again and properly torque the bolts. So, I really created another problem during the diagnosis.

turn off breaker
turn off water supply line
note wire color locations on notepad
disconnect 2 spade lugs (pliers)
disconnect inlet line (adj. wrench)
disconnect outlet line (pliers on hose clamp)
remove old valve assembly (4 screws w/nutdriver)
remove ground jumper from old valve
remove inlet pipe ell from old unit (vise & pliers)
clean open end of pipe ell (file)
apply teflon dope tape to pipe threads
install pipe ell on new valve
reorient solenoid 90degrees cw to match Maytag installation
reinstall ground jumper
install new valve assembly in dishwasher
reconnect hose and hose clamp
reconnect inlet line
reconnect spade lugs
turn on supply line, check for leaks
turn on breaker
start washer at appropriate cycle to test water flow
done!

The replacement part was the perfect size but the threading on the terminal ends was increases to 1/2" v the 7/16" from the previous element. My first attempt was to find a similar type of part at the local hardware store(not a superstore)since I planned to replace the grommets anyway. After not having any success, I came home and modified the fasteners by slowly drilling out the id of the fasteners until they threaded properly. The time to replace after the drill out was less than 10 min and the ~$45.00 is significantly less than $450.00 for a new unit.
If I would ask anything of part select, it would be to include fastening hardware as re-engineering of products is a continual process.

First, I searched the repair help on this site to see what others did to repair their diswashers, and it looked easy, so I just followed the same instructions. First, I used a hex star key wrench to remove the screws that hold in the interior door cover. I disconnected the leads to the defective wax motor, reconnected the leads to the new motor and screwed the door back together. It took 15-20 minutes and was a piece of cake! My first appliance repair, and as a single woman and first-time homeowner, I was really impressed with this site! It gave me confidence to tackle more home repairs instead of calling for service and getting raked over the coals.

First unplug the unit. Open door. Take a special tool to remove all the screws (star shaped) around the edge of the door, and remove plastic panel where motor for detergent cup sits. Remove wires (two) from the motor. Remove wax motor by unsnapping motor from its cradle--comes out by moving the fingers holding it in. Push new motor into position, being sure the round pin sticking out at the end (on the left side) so that it sits in the groove made for it. Replace panel and screws, plug power cable back into its box. Close detergent cup door, turm on dishwasher, run through cycle, open door and check to see if detergent door opened up. If it did, then fill with dishes and wash.

Piece of cake. I panicked for a minute before I realized that there was a threaded brass 90 in the inlet valve. It looked like it was the wrong part for a minute. Once I got the 90 reinstalled in the new valve, I had it back together in 10 minutes. It seems to be working better.

I took off the front bottom panel for an easy access. The valve is located on the left. Shut off water to the dishwasher. Remove the bracket that holds the valve. Remove hoses and 2 wires on the valve switch. Install new valve by revesing the steps above.