Models > HDA1000Z12WH > Instructions

HDA1000Z12WH Hotpoint Dishwasher - Instructions

Jump to:

All Instructions for the HDA1000Z12WH

Customer:: Harry from Bayside, NY
Parts Used:: WD08X10057
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins

Small leak at the bottom of dishwasher

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

Was this instruction helpful to you?

Customer:: karen from oregon, MO
Parts Used:: WD15X10003
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

dishwasher would not fill with water and cycle

first off if you can understand the problem DO NOT CALL THE GE REPAIR SERVICE AND HAVE A REPAIRMAN COME TO YOUR HOME you will save over $300.00. a mistake i made, it cost me $79.95 just for him to tell me the dishwasher was broken and then i was told it would cost me over $300.00 to fix it. WHEN I TALKED TO PARTSELECT I FOUND THE WATERVALVE FOR A LITTLE OVER $55.00 WITH SHIPPING IT TOOK ABOUT 20 MINUTES TO DISCONNECT THE DISHWASHER AND REMOVE THE OLD PART AND ABOUT THE SAME AMOUNT OF TIME TO REPLACE THE NEW ONE THEY EVEN HAD GOOD INSTRUCTIONS IF YOU NEEDED THEM. I FOUND PARTSELECT SERVICE TO BE A VERY GOOD BUSINESS TO WORK WITH. ROY F BURTNETT

Was this instruction helpful to you?

Customer:: Michael from Oronogo, MO
Parts Used:: WD08X10057
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

existing gasket dry rotted

This repoair was needed due to diswasher leaking out of side door. I just moved in about 6 months ago and needed to use dishwasher. When it leaked i noticed it was in need of a gasket. I searched the internet and came accross "part select". Part showed up in less than 3 days and was a breeze to install. The original gasket came out just by pulling, cleaned up channel and installed new gasket.slid in real easy. I did take off inner door panel to inspect for any damage. none noted. Perfect fit first time. Dont get confused folks if the part has another name as some parts are interchangeable in the industry.

Was this instruction helpful to you?

Customer:: Thomas E from Lexington, SC
Parts Used:: WD15X10003
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers, Wrench set

water leaking on floor under dishwasher

Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one

Was this instruction helpful to you?

Customer:: ELLIS from MADISON, AL
Parts Used:: WD15X10003
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Wrench (Adjustable)

Water leaking from beneath dishwater

It took no time at all to identify where the water was leaking from. I accessed a parts breakdown illustration of my dishwasher, identified the part, ordered it and three days later my leak was fixed. Hose and water inlet valve assembly was easy to swap out. I estimate I saved myself about $150.00 by doing it myself.

Was this instruction helpful to you?

Customer:: steve from Rockford, IL
Parts Used:: WD15X10003
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Socket set, Wrench set

Dishwasher was left outside and the water inlet valve froze

We we're installing a used dishwasher,had to take it back out and replace the water inlet valve.

Was this instruction helpful to you?

Customer:: Nick from Kalamazoo, MI
Parts Used:: WD15X10003
Difficulty Level:: Easy
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers, Wrench set

Valve failed and washer overflowed.

Immediately shut off water supply to the washer. After ordering and receipt ot part: Removed base panel, turned off power, disconnected wire, water supply line and screws attaching washer to kitchen counter. Pulled the washer out and turned it on its side with the valve on top. Removed and replaced the valve, returned the washer to the upright position, pushed it back under the counter, reconnected all services, screws to counter and base panel, turned on the water and power. Took two hours since I needed take a trip to the hardware store to replace a right angle water fitting .

Was this instruction helpful to you?

Customer:: william from camanche, IA
Parts Used:: WD21X10060
Difficulty Level:: Really Easy
Total Repair Time:: 1- 2 hours
Tools:: Pliers, Screw drivers, Socket set

would not drain

replace solenoid

Was this instruction helpful to you?

Customer:: John from Havertown, PA
Parts Used:: WD15X10003
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Socket set

water was leaking from the inlet valve

the repair would have been much easier but the screws from the old inlet valve did not match the size of the holes on the new valve.

Was this instruction helpful to you?

Customer:: Steve from Cibolo, TX
Parts Used:: WD15X10003
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers, Wrench set

Water Inlet Filter

Before you due anything else...remove the water inlet valve, remove the 4 screws holding the water inlet coupling to the valve housing, remove the nylon filter (tight fit), and clean the debris from the filter. Re insert the filter, reassemble the valve housing and check for leaks. Clears most water flow problems.

Was this instruction helpful to you?

Customer:: BILLY from SAN LUIS, CO
Parts Used:: WD15X10003
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set, Wrench (Adjustable)

Valve was leaking. This is the second one that has leaked.

Remove front shields on bottom of dishwasher. Shut off dishwasher and electricity. Unplug electric connection. Unscrew brace holder screws on front. Remove clamped on hose at back of valve. Unscrew valve from copper water pipe. Screw on new valve to copper water pipe. Put on clamped hose. Screw on bracket. Plug in electric connection.

Was this instruction helpful to you?

Customer:: Delia from Ocean, NJ
Parts Used:: WD08X10057
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins

no water was being supplied during certain cycle

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.

Was this instruction helpful to you?

Customer:: Richard from Bay Village, OH
Parts Used:: WD15X10003
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

water inlet valve stuck open (frozen??)

after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!

Was this instruction helpful to you?

Customer:: Carlon from McRae, AR
Parts Used:: WD15X10003
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Water would not fill.

Wow, could not have been easier. The suggested repair stated that the water inlet valve was the problem 93% of the time. And, it was spot on. It was the exact same replacement part. And, once installed, it worked like a charm. I have bookmarked this website, and will use it for all future appliance repair. I simply could not be more pleased. It was a breeze. Thanks,

Was this instruction helpful to you?

Customer:: Robert from Willcox, AZ
Parts Used:: WD19X10032
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Leaking motor seal

Followed easy instructions and completed repair in less than 30 minutes.

Was this instruction helpful to you?

All Instructions for the HDA1000Z12WH