HLD4040M15SA Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Georgetown, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Plastic part of inlet valve cracked
Hired my neighbor, who is a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irma from Smyrna, GA
- Parts Used:
- WD35X21035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Upper Rack Wheel and Stud Assembly
I removed top dishwasher rack, popped off broken studs, and removed wheels from the tracks. I replaced studs on rack by popping them into place, and I slid new wheels back into wheel tracks. I place new studs into wheel assembly, slid rack back into dishwasher and replaced stoppers at the front of the tracks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from GLEN ALLEN, VA
- Parts Used:
- WD05X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Dishes were not drying inside the dishwasher after the dishwasher cycle completed
The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from GREENVILLE, SC
- Parts Used:
- WH23X10028
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Did not drain water
Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SOUTHPORT, NC
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from DEERFIELD, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
One axle cracked and broke off; another wheel was had fallen off and was distorted when it hit the heating element.
Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from THE VILLAGES, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the lower rack of our dishwasher kept falling off.
Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Terra Ceia, FL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
The water valve went out
I took the old one off and replaced it with the new one, which fir perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from PALERMO, ME
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing wheels
The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan M. from AYER, MA
- Parts Used:
- WD26X22719
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Drain pump failed.
Ordered drain pump kit (GE part # 325). When it came it looked different from the pictures in the manual and what was ordered. Thought I was going to have to retrofit pump. Looked at ordering a drain kit from another source, which I did. When that came it was exactly the same as the one I ordered from Part Select. I returned the other pump.
Looking at the parts diagram, I discovered the replacement pump (part # 325 ordered) was combined with part # 327 which is why it looked different. I went ahead with the replacement, pulling out the pump and the connecting tubing, part # 327. The replacement pump fit exactly in place, replacing the pump and tubing. I put the dishwashing machine back together and it works great.
Bench tested the old pump and it worked. It must have had a food ball caught in the impeller, inhibiting flow. Next time I'll check all the parts for grease and food balls before ordering new parts..
Looking at the parts diagram, I discovered the replacement pump (part # 325 ordered) was combined with part # 327 which is why it looked different. I went ahead with the replacement, pulling out the pump and the connecting tubing, part # 327. The replacement pump fit exactly in place, replacing the pump and tubing. I put the dishwashing machine back together and it works great.
Bench tested the old pump and it worked. It must have had a food ball caught in the impeller, inhibiting flow. Next time I'll check all the parts for grease and food balls before ordering new parts..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from GROVE CITY, OH
- Parts Used:
- WD01X10099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The plastic part was broken from the pulley
After I unscrewed it from the counter and took off the front panel I first went to the garage to turn off the power to the dishwasher. I then pulled it out a little bit at a time. I didn't want to take apart any hoses or unplug electrical wires from connectors if I didn't have to. I then looked underneath and noticed that only one pulley spring was off and the plastic piece was broken. So when I received it in the part in the mail I took of the plastic part from the pulley. I just reused the original wire pully. I reached back with the spring to hook it back on with some difficulty and then hooked the piece back on and it was done. I placed everything back and switched the power on and its good to go. Nice job to do myself and watch a Youtube video on how to do it.
Was this instruction helpful to you?
Thank you for voting!