SUF2100E*119 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Atlanta, GA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Water wouldn't fully drain from dishwasher
I reinstalled a new piston/nut assembly which was easy as per this forum. The two compared side to side clearly showed my old one as worn out and deteriorated. This however wasn't the only problem. Once new piston/nut assembly was installed the water still did not drain. I pulled the dishwasher out from the cabinet, disconnected the hose connected from the pump to the outer box the piston/nut assembly connected to and flushed that out. I discovered two pieces of broken glass in the box that may have been blocking the rubber flapper connecting the box to the drain hose. Glass was removed and once all was reconnected the unit drained perfectly. Check for potential debris in outer piston/nut assembly piece if simple change out of of piston/nut assembly doesn't solve the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Lincoln, NE
- Parts Used:
- WD24X10018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Dishwasher wouldn't drain after washing cycle
We went to the Part Select site and described the problem and they recommended a new piston and nut assembly and even provided a video on the installation. The only difficulty was removing the old piston and nut assembly which was corroded and broke off during removal. Once it was out installing the new part was very easy. And best of all the dishwasher completely drains. We had an estimate of $150 for a repair house call which would probably have resulted in another house call to actually install the part. With Part Select we received the part the next day, spent only about $18 and fixed the dishwasher in 24 hours--what a great experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from lexington, NC
- Parts Used:
- WD15X93
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Old valve had hairline crack and leaking
2 screws to remove valve, turn water off, detach water line, detach plastic water outlet line, and put the new one on, reattaching everything in reverse. Electrical hookup was just two wires to solenoid. Slipped them off and back on new valve solenoid. Some difficulty getting support screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Chalfont, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dishwasher not draining, water left in bottom when cycle completed
Thought hoses were clogged. Cleaned hoses but no obstructions. Googled the problem and found many similar problems. On PartSelect, the Piston and Nut Assembly was found to be the problem 44% of the time. I ordered the part and it arrived two days later. PartSelect showed how to install it and the problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from ham lake, MN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
did not pump out all the water before drying
looked up the model no. on partselect web site and they discribed several diagnoses for different problems.they gave a 19% probability for a bad valve and nut. i removed the cover and the nut valve and the valve looked pretty bad. i ordered a new part and delivery was very good.i replaced the part and that took care of my problem. i was very happy with the whole repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Saint Louis,, MO
- Parts Used:
- WD28X265
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
multiple rust spots on the old rack
Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from bluffton, SC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishwasher would not empty, your list of potential problems was an excellent guide plus the online schmatics
used tips from a past buyer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from port clinton, OH
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
when dishwasher was turned on no water sprayed out the rotating arm
I diconected the electric removed water line removed 2 hex head screws pulled out inlet valve squeezed the pressure clamp and pulled off water inlet line and re assembled very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Syl from Pagosa Springs, AL
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not turn on the water
took off old part, put on new part and that was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Romoland, CA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken vent on microwave
Ordered the part and installed...easy and great prices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Central Square, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Rubber piston on check valve was almost completely gone. Water backed up finally to the point of overflowing on kitchen floor.
Simply followed the instructions for the part on the part page. One thing that helped taking out some screws was to remove a couple of the brackets that hold the heating element and move it slightly. I would suggest cleaning all of the gunk out of drains and clean all holes in the screens using a toothpick, etc. Be careful not to overtighten the nut for the next time you have to do this!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from EAST ROCKAWAY, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water Would Not Drain
Went on line to order new pump. Web site showed "parts which repaired this problem and nut and valve had very high % as the failed part". I then removed nut and valve and was able to see that it was worn as they described. This was a very easy repair and worked perfectly. It saved me from ordering a $60. 00 Pump which would not have fixed my problem. Thank you for a great help for the diys people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from New York, NY
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing silverware basket
part came in the mail and fit the missing space perfectly. no complaints. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Seattle, WA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Dishwasher wasn't draining
After some investigation on the internet and partselect.com, ordered and replaced the piston and nut assembly inside the back of the dishwasher and the problem was fixed.
Was this instruction helpful to you?
Thank you for voting!