GDT545PGJ5BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter A from HOLLAND, MI
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber Coating worn off rack...causing Plates to get rusty on their edges.
Open box...remove old rack from dishwasher...roll in NEW rack. Done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corinna from MOUNT AIRY, MD
- Parts Used:
- WD08X21894
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Door gasket needed to be replaced
Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Cassopolis, MI
- Parts Used:
- WD19X25187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
would not drain water
2 hose clamps, connect the wire with the wire adaptor suppled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from FALLS CHURCH, VA
- Parts Used:
- WD21X31910
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Buttons unresponsive/UI replacement needed
I was very confident that the problem with my GE Adora DDT595SSJ5SS was that it needed a new UI board. It had been beeping randomly for a couple of months, requiring a circuit breaker reset every so often, until finally it stopped working entirely. When I looked at the main board underneath, the LED was flashing too fast for me to count the blinks. These were the signature signs of the UI board going out -- and this did indeed turn out to be the problem. I've run the dishwasher several times since replacing the board, and there have been no issues.
The only real issue I had with the repair job was removing the dishwasher door. This was because the door of my model was held in place by a pair of tension cables (bottom left and bottom right of the unit), rather than hinges, and the cable method of attachment is less documented online. I had to get hold of a user manual for my unit to even discover this fact about it, since I had purchased my home with this dishwasher already present and did not see it being installed originally.
What I had to do was to pull the unit out about five inches, exposing the attachments for these cables (they are on the outside of the unit), so I could hook my heavy wire hook under them and detach them. If your dishwasher has these cables on the door, you really do need a hook tool of some sort to remove them. If you have strong wire, you can make one yourself as I did. Anyway, removing the cables allowed me to remove the door. After that it was straightforward to unscrew and unbolt the various panels, set the jumpers on the new UI board, and screw everything back together.
I should note that the cables were not tricky in any way, just that all of these Adora units seem to be a bit different and I happened to have one with a method of attaching the door that is not very well documented. I hope that this helps someone with this type of unit. If you see those videos online referring to detaching the door from hinges, and you can't find anything on yours that looks or feels like that, consider that you might have cables instead on the outside of the unit.
The only real issue I had with the repair job was removing the dishwasher door. This was because the door of my model was held in place by a pair of tension cables (bottom left and bottom right of the unit), rather than hinges, and the cable method of attachment is less documented online. I had to get hold of a user manual for my unit to even discover this fact about it, since I had purchased my home with this dishwasher already present and did not see it being installed originally.
What I had to do was to pull the unit out about five inches, exposing the attachments for these cables (they are on the outside of the unit), so I could hook my heavy wire hook under them and detach them. If your dishwasher has these cables on the door, you really do need a hook tool of some sort to remove them. If you have strong wire, you can make one yourself as I did. Anyway, removing the cables allowed me to remove the door. After that it was straightforward to unscrew and unbolt the various panels, set the jumpers on the new UI board, and screw everything back together.
I should note that the cables were not tricky in any way, just that all of these Adora units seem to be a bit different and I happened to have one with a method of attaching the door that is not very well documented. I hope that this helps someone with this type of unit. If you see those videos online referring to detaching the door from hinges, and you can't find anything on yours that looks or feels like that, consider that you might have cables instead on the outside of the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from STERLING, CO
- Parts Used:
- WD05X30818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher was not drying
I followed the U tube instructions already put out part select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from SPRING, TX
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old lower rack was rusted
Opened the box took the rack out and placed it in the dishwasher. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MYRTLE BEACH, SC
- Parts Used:
- WD28X35779, WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Racks were rusted.
Ordered new parts, unpacked the shipping containers, removed old racks and inserted the new ones. piece of cake. Perfect fit and prompt service.
Was this instruction helpful to you?
Thank you for voting!