GDT545PGJ5BB General Electric Dishwasher - Instructions

Not having to screw with the hose clamps is the advantage here!
Disconnect electric connection at motor.
Slightly bend tabs that hold the pump to motor, twist motor from volute.
Do this on old pump first to get a feel for how easy the tabs can be broken
Do same on the replacement pump, put new motor on, watch alignment
can be a bit tricky.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

Pulled dishwasher out switch is on very bottom of pump housing, turned dishwasher on its back, took out 1/4" bolt holding on bottom of switch frame, took two very small screwdrivers and small picks to hold open switch clips, while switch was removed checked float for frew movement, put in new switch, removed screw drivers and picks checked to see all locked on new switch in position, replaced bottom plate and bolt, checked burner reset all good now dishwasher heats and drys!

The old gasket pulled right out with no tools needed,
The new gasket went in the same way.

Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.

Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

I watched a YouTube video that showed how to to do this. The first trick is finding the right video. This one worked best for me / my model.

https://www.youtube.com/watch?v=sesf0BS8fzM

The first few I watched were for models with the user display on the top of the door, and you have to open the dishwasher to see it. Mine shows the display on the outside. Look for the video that has a round plastic "vent" on the inside of the door. You will have to loosen it with some sort of tool in order to remove the display once you get the door taken apart. In the video, they used needle-nose pliers opened wide. My NN pliers don't open that wide, so I used two screw drivers. Pealing off the display is a bit challenging. I was afraid I was going to break the little plastic pins that hold it on. The rest is not too hard though, and it went back together quite easily, even though I did break a plastic piece that 0ne of the UI Control Board screws goes into. Oh well, now it has three screws holding it instead of four.

Don't remove the door! Unscrew the bolts at each lower corner of the door(this is how the door is attached to the hinges so it is now free). Then open the door fully and slowly pull the door toward you a few inches. This slides the door up the hinges and allows just enough room to slide the old gasket out and and slide the new one in. Then slide the door back down the hinges(pushing it away from you, back into place). Then simply close the door and reinstall the bolts at the bottom corners and all done! I watched several videos and believe me, removing the door to replace this gasket does nothing but turn and small quick repair into a large lengthy one.

Downloaded the GE manual from the internet. Followed the GE repair manual trouble shooting guide. The manual contains all of the disassembly and reassembly instructions. Main board had a more than one volt higher than listed voltage output. Manual does not list an acceptable voltage range so I ordered a new main board. New board had the same output and did not fix the problem. I ordered a new UI board. The new board is a genuine GE "programable" replacement board that covers multiple models.
I set the indicated jumper to the required position for my application and installed it. The problem was not corrected. I read that some people had problems with defective replacement boards so I contacted PartSelect to return the first two boards and reordered the UI board.
I once again set the jumper and installed the UI board and it worked immediately.
The whole repair was extremely easy. PartSelect is very good to work with. I had no problems with returns or refunds. I will definitely use them again if I have the need for any of their products. There were slightly cheaper suppliers, but PartSelect had the parts I needed in stock and they shipped my order lightning fast. They are more than worth the few extra pennies difference.

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

Simple answer- do not try to do this. GE makes you replace the entire door to replace this $3 part or call them and pay $100s to fix it. We decided to replace the entire dishwasher after we went through disassembly (there are no instructions on this) only to find out we could not fix without a brand new door.

The repair is easy for most if you have basic skills.

1. Cycle your unit to make sure all the water in the tub is emptied. (Start a cycle then cancel it which forces it to empty)

2. Turn off the power at the circuit/fuse panel & also turn off your water supply going to the unit which is usually under the sink with your sink plumbing.

3. Have a few old towels handy, there will be a little water but nothing that requires a wet shop vac, etc.

4. Remove the bottom kickplate (should be a screw on each side of the front of unit)

5. Disconnect the power supply wiring to make removal easier.

6. Disconnect the water supply line (have a towel handy there will be a little water in the supply line)

7. Unscrew the mounts either at the top and/or sides of the washer depending on the install method into your cabinetry.

8. Carefully slide out the unit.

9. Carefully turn the unit on its side or upside down depending on your preference to work on the underside where the pump is located. Again have a towel or two handy there will be some water that leaks out from the tub even after forcing an empty cycle.

10. The circulation pump is easy to remove. First plug the power line, there is a clip to disengage to separate the plug. A small flat screwdriver will help.

11. If this is a first time being replaced it will probably have crimp style hose clamps on the two lines coming off the pump. Again a small screwdriver will help pry it apart. Throw these away your pump kit will have new hose clamps for installation.

12. Once these clamps are removed you can slip the hoses off and the pump will be free to remove from the unit.

13. Installation is easy. Make sure the rubber hoses seal completely around the unit before clamping. Pay attention to make sure its sealed evenly, your unit will leak water otherwise once its functioning again.

14. My recommendation is to reassemble, slide the unit back into your cabinetry and hook your power and water supply up. Before you screw the unit back into place and close up the bottom panel, start a quick cycle. Within that first minute when the unit is filling and starting the circulation pump you can watch underneath and make sure your circulation pump lines are sealed and not leaking. Once satisfied, you can then stop the unit and finish securing the unit with mounting screws and closing up the bottom kickplate panel.

Good luck! You can do this :)

My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.