41200149 General Electric Dishwasher - Instructions

easiest way i found to do it was pull dishwashers out from under the cabnet... laided a pillow down in front of the door and turned it on the front side... the part was very easy to get to at this angle....could have done it in less then 5 minutes but took my time to double check everything to be safe....took a total of about 10 minutes..... very happy now no longer need to vacume out the old dish water left at the bottom of the dishwasher...... i think most anyone could do this very easy....

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Each replacement wheel came in two parts: the wheel itself and the clip which had to be pushed through the center hole in the wheel in order to attach each wheel to the carriage that holds dishes. I had difficulty assembling the clips and wheels until I ran the clips under hot water to soften them. This made it possible to assemble the wheels and attach them to the dish carriage. I would have preferred the wheels to have come assembled, particularly given the price of each one.

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

It turned out to be an easier job than I thought it was going to be. Of course, I was still a bit surprised it worked right and didn't leak once I was done.

I started by taking off the servo that opens up the drain valve. I didn't think I could take out and replace the shaft seal from this position so I took the whole motor and drain assembly out by loosening the sump and pump clamps. This allowed me to wiggle out the whole mechanism. One plug and a ground wire had to be undone but that was it. The Push On Nut was the worst part - pain to take off - worse to get a new one on. I wasn't sure (still not) if I could get it in the right place. Once I got everything back together and the servo mount on it seemed to hold the nut in the right place.

I tested it and yelled "it doesn't leak!" my wife promptly said "Yet!".

We have run the dishwasher twice - so far - no leaks!

I couldn't have done it with out PartSelect's prompt service, diagrams, and part photos. I don't want to fix any more appliances but if I have to PartSelect is where I'll come for parts and diagrams.

Based on what I read from other people and partselect, it was fairly easy to ascertain what was wrong. I removed the solonoid valve by removing the two screws that held in place. Had to clean up the solonoid valve rod due to water leaking into it by running it on a wire brush. Pulled out the stop nut and old seal and replaced it with the new seal. Could not get the new stop nut on but it does not seem to move so let it go. Have to say that reading all the comments certainly helped me with the repair. Additionally, ordered parts by email at 10:30 in the morning and receiving them the very next day. Could not believe they were delivered so quickly.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!