41200149 General Electric Dishwasher - Instructions

over time the upper rack axles broke so the rack would just come out of the rollers. I ordered the parts from here and had to youtube how to get the stops out so I didn't have to unscrew the metal guides out making an easy job into a hard one. all you have to do is with a flat head screw driver is slightly bend the plastic end part of the stop which is in the metal guide that stops the wheels from coming out of the guides. once you bend out the plastic end you then turn the stop to get it out of the metal guides. if you youtube it its very easy. just be easy when you bend the plastic piece because I can see it breaking. I didn't break mine so the job was very very easy and took all of about 5 to 10 minutes to complete the entire job. I love this site it had real life info to help out when you need to do a job and trouble shoot your appliance.

Pop the end caps off the slides by pushing the lock tab in with a medium flat screwdriver, through the square hole in the side of the slide. Pull the rack out and set it on the counter. Pop the axles off, with the rollers, with your fingers. They are just clipped on to the rack wire. Pop the new ones on 4 places, fingers only needed to clip them to the wire. Put the rack back in the dishwasher by aligning the rollers in the metal slides and pushing it in like normal. Pop the rack slide end caps in by just pushing them in. If you're smart you bought new ones, they're cheap insurance. Save any good used parts in your kitchen junk drawer for the next time you treat it rough. Less than 5 minutes to fix. So easy a caveman could do it. One just did!

The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.

Snapped right in

Replaced door seal and corner seals. Be sure to heat door seal in dryer be for instillation, 2 minutes. Makes for an easy installation.

Removed rack slide end caps. They broke off because of brittleness. Removed rack, then used pliers and/or flat blade screwdriver to remove 4 rollers and axle assemblies. Replaced with new rollers/axles. Return upper rack into slides and installed new end caps. New caps slightly different than old but easily clip into place Upper rack works lile new!

My GE Potscrubber 940 would not drain on all cycles. After checking the basin traps and not finding any blockage in the water drain line, I suspected that the problem was with the drain solenoid, since the motor was running smooth. I removed the dishwasher, primarily by removing the water supply line on the left side from the water inlet valve and disconnecting the electrical connections. Make sure you turn off the water and electricity before you do any work on the dishwasher. With the dishwasher taken out and on its side, the drain solenoid unit will be visible near the motor in the middle assuming that the front bottom panel of the dishwasher has been removed. I found mine to be all crudded up. I removed the electrical connections and the solenoid bracket. Then by using my multimeter, I found a bad resistance reading (infinity) for the solenoid. I ordered the Drain Solenoid Repair Kit and replaced all the items except the plastic rocker arm. Naturally, just reverse your steps to get the dishwasher back together. Turn the water and electricity back on and fire her up. Check for proper operation and any leaks and you should be done.

Pulled washer out about 6" without disconnecting any hoses. This way i could use both hands from the left side & front after i took the kick plate off.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

I would like to start-off by saying that I love this site . I've never been even remotely dissatisfied with parts I've ordered and the installation videos are awesome! I would recommend this site to anyone looking to repair appliances. Secondly, I am a retired mechanical designer with over 35 years of experience. I have a broad range of design experience in consumer, governmental, industrial and military part and product design. My opinion about the design having to do directly with my appliance is not very high and after talking with another local parts supplier discovered that this particular design is approximately 20 years old. I wonder how many dishwashers are leaking without the consumer realizing they have this problem. I followed the installation instructions provided by this site verbatim and the dishwasher still leaked like a sieve. This in my opinion goes back to my remarks concerning the design. This is a weak design at best and could benefit from an improvement in that area. After I installed the new parts, the push on nut (upon being seated onto the shaft for the drain valve flapper) was loose and spun freely. The push on nut did not properly compress the seal onto and around the flapper shaft nor into the valve housing. Water leaked through the seal as a result. I disassembled all of the parts again and placed a flat washer between the push on nut and the seal, to help compress the seal onto the flapper shaft and into the valve housing. The washer was a stainless steel flat washer with an ID that fit onto the shaft closely, but was a smaller OD than the seal. The washer was about 1/32" thick. Upon reassembly and observation, the dishwasher leak was stopped with the addition of the flat washer and my issue was resolved.

The repair was as simple as it could be. The real story is being able to find and replace the missing wheels. Your website makes it real simple to find the proper parts, order them and receive them in a few days. Your parts person; Jason was very nice to send me a little note concerning my order. I appreciate that personal touch. I will be a regular customer with that kind of service. Well done/Good Job.
Bill

My suggestion is to replace all four rollers at the same time since they are all the same age. Fortunately, four rollers come in each pack you order. You need to remove the end cap on borh metal rack rods which takes a little doing. You cannot just pull the caps off. You need to twist the end cap to free up the little catch at the rear of the end cap. Once the end caps are off, just pull of the old rollers and install the new ones, replace the end caps and you're done.

installed new rollers per diagram then installed side ends into sides. Couldn`t have been easier. Dishwasher is like new now.

The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.

First I removed the four screws holding on two metal panels to gain access to the springs. Then I unhooked the broken assembly from the springs. Then I hooked the new assembly to the hinge. Finally, I reconnected the assembly to the springs. (I didn't have to unhook the assembly from the hinge because it had already broken off.)

This part must be one of those that commonly goes because I had replaced the other side about a year ago. The most difficult part a year ago was diagnosing the problem and figuring out how the pieces fit together. This now it was a quick repair because I knew exactly how to fix it. (And thanks to PartSelect for delivering the part in 48 hours even though I didn't pay for quick delivery.)