GHSD511P00BB General Electric Dishwasher - Instructions

Repair was easy. However, this did not solve the problem.

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!

Ordered the Drain Valve Shaft Seal and Push On Nut to make repair. Removed dishwasher from counter. Removed motor/pump assembly from dishwasher. Removed drain celenoid from pump. Removed old push on nut and old drain valve seal. Installed new seal and push nut. Replaced everything in reverse order. Amazingly no water leaks after reinstallation. Seams to be working fine so far....fingers crossed. Hoping to get a few more years out of this dishwasher.
Thank You PartSelect.

My GE dishwasher had a problem. The upper rack would fall into the lower rack when loaded breaking dishes! Turns out, the front rollers on the upper rack were broken so that the supports would just pull out. So, I found the parts on this website easily. I then took off the plastic plug on the support which is easy to do. There is a flange you bend towards the rear of the dishwasher to release the plug. Once released you have access to the rollers, which just snap off easily. The new ones snap on easily. Reverse the cap removal, and you are done!

Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy

Followed the very excellent instructions provided on website by Hotpoint/GE

Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.

UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS

There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.

Installed new lower rack wheel kit

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

Super-easy and quick repair -- quality part snapped right into place.