40410148 General Electric Dishwasher - Instructions

I followed the video instructions on removing the rack slide end cap to prevent breaking it and it was very easy to remove and replace the broken one. I attached the new rack rollers and voila we were back in business. I was about to order a new dishwasher the night before for $5oo! Thankfully the stores website wasn't working so I couldn't. I decided to look online to find out if it was easy just to replace the parts. Looks like I saved close to $500 just replacing those parts! AWESOME!!!!!Thank you for a user friendly website. It made all the difference")

Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.

Removed screen bottom rear andfound a plunger type part, unscrewed plunger and found it was distressed around it and did not close of a tight seal. Placed new part into location and dishwasher now proforms perfect...

The rack for my model has been discontinued so they shipped me the replacement version. The wheels on the new one are skinnier than the original model so I had to remove them and replace them with the wheels from the old rack for it to fit/roll correctly. The new wheels were a little tricky to get off as I had to use a screw driver and basically manipulate/pry apart the clamps that hold them on. The old wheels just snap on.

I looked at your web sight and saw how to repair dishwasher.

this unit is 29yrs old. I used your directions, just took a little time to make sure how to put together. All went well

Replacing the two corner baffles was the third attempt to stopping the leak. I first replaced the door seal without removing the inner door and the leak did not stop. Then I removed the inner door, reinstalled the door along the bottom and added the small seal required at the lower center portion which is separate than the longer door seal. Still leaked! Then I replaced the corner baffles and alas., the leak stopped. I would recommend that all seals be replaced at the same time. Total cost about $40.00 and can easily be done in one hour or less. I ordered the parts And they arrived remarkably in les than 24 House with regular delivery. Very pleased with Parts Select instructions and service!

Fiddled with the rollers until figuring out how to remove them. Hardest part was getting the stops off the ends of the roller guides. Replaced rollers, replaced rack, replaced ends of roller guides. Voila

Remove wooden top and pulled out hose from spray arm. Removed spray arm. Installed top hose fitting using a bit of silicone grease for ease of installation. Reinstall spray arm. Stuff hose in same position as old hose. Lay dishwasher on it's back and remove old hose from pump by removing clamp. Replace new hose in same position and reclamp. Stand dishwasher back up and reinstall top. Wife is now happy! I could do this again in half of the time.

Replaced both corner tub baffles but did not correct the problem.

Replaced the lower right and lower left corner tub baffles

Removed filter screen with the socket set, removed the piston and nut assembly with pliers, and installed the new piston and nut assembly. Put filter screen back in with hex head screws. During the process, I opened the float regulator and cleaned it out too. Water backup problems solved.

removed screen at back of dishwasher from the inside. Twisted piston & nut assembly out by hand and replaced with new one. Very, very simple. Dishwasher works perfectly now.

It really was very simple. The parts just snapped together and then snapped into place on the rack.

First I opened the dishwasher and removed the lower basket. Next I removed the 4 screws that hold the food filter plate in place at the back of the tub. Then I unscrewed the Piston/Check Valve assembly counterclockwise, located at the back center of the tub, by hand. I replaced the old part with the new one and reinstalled the filter plate. I ran a rinse cycle to verify that that all of the water was purged. Finally, I reinstalled the lower basket and resumed using my dishwasher.