40410148 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenda from NORMAN, OK
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rack of the dishwasher had broken rollers.
Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Vacaville, CA
- Parts Used:
- WD12X271
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lost 2 front wheels.
There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from BROWNSTOWN, MI
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Axles had broken, leaving the tray falling down when pulled out too far.
Followed the very excellent instructions provided on website by Hotpoint/GE
Was this instruction helpful to you?
Thank you for voting!
leaking from door
researched the problem, listened to you tube, ordered the parts
and did the repair. Very easy to do, only took a few minutes.
and did the repair. Very easy to do, only took a few minutes.
Was this instruction helpful to you?
Thank you for voting!
Tub Baffles Disintegrated & Door Cable Broken
I used Partselect.com website to educate myself on parts needed for my model of dishwasher. Also reviewed repair instructions by others on the website and learned repair and replacement was straight forward and simple. I ordered parts from Partselect.com, they came promptly, and were the correct parts. Based on the repair instructions, I removed the fascia panel at the bottom of my dishwasher to expose the cable and spring setup for my model dishwasher, cleaned the area and installed the new parts - it took only a few minutes - then I replaced the panel and secured it with the sheet metal screws that were holding it in place. I opened the dishwasher door. My wife had already cleaned the corners of the tub where the old baffles had been, so I pressed the new baffles into place with my fingers - no tools were required for baffle installation. Dishwasher is back in service; thanks to the information, parts and prompt service provided by Partselect.com ! My wife is pleased and so am I.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thevinh from El Monte, CA
- Parts Used:
- WD7X14
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
one cable was boken
1 - unscrew that holded the machine in place, these screws were on the top of machine.
2 - pull out machine about 5 inches.
3 - unscrew the cover at the bottom cover. there were 4 screws, 2 on the left and 2 on the right.
4 - connect 2 cables in series with 2 springs.
5 - hook one end of 1st cable to the left pin and the other end of 2nd cable to the right pin.
6 - slide both cables lay on both wheels.
7 - Tight all 4 screws back to their place and push machine in place.
8 - tight the last 2 screw which hold machine in place.
2 - pull out machine about 5 inches.
3 - unscrew the cover at the bottom cover. there were 4 screws, 2 on the left and 2 on the right.
4 - connect 2 cables in series with 2 springs.
5 - hook one end of 1st cable to the left pin and the other end of 2nd cable to the right pin.
6 - slide both cables lay on both wheels.
7 - Tight all 4 screws back to their place and push machine in place.
8 - tight the last 2 screw which hold machine in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from tampa, FL
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water left in dishwasher after wash
Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allen from grove city, PA
- Parts Used:
- WD12X10304, WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
upper rack dificult to rol
removed the end caps and took the rack out of the dish washer.
found right front rack roller bad and replaced.
slide rack back into dishwasher and replace end caps.
found right front rack roller bad and replaced.
slide rack back into dishwasher and replace end caps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from DOWNINGTOWN, PA
- Parts Used:
- WD35X21038, WD8X229, WD8X228, WD8X227
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Dishwasher was leaking at bottom of door.
Removed the corner baffles by lifting up and out. Cleaned the area and pushed new replacements in position.
Removed door seal by pulling on the end.
Press new seal in to the slot. Work in to slot a tree ound door.
Removed door seal by pulling on the end.
Press new seal in to the slot. Work in to slot a tree ound door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geoffrey from Centreville, VA
- Parts Used:
- WD7X14
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cable broke to the spring attachment for tension on the door.
The cable attachment comes with the two hole loop assembly that the springs hook into. With the lower panel off and the door closed, the other end of the cable assembly hooks onto the fitting on the side of the door. No tools required except the phillips head screw driver to take off the lower panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Glendora, CA
- Parts Used:
- WD7X14
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher door become very heavy - cable broke
Remove the bottom two panels below the dishwasher door. There are two phillips screws and two nut screws.
Replace the broken cable by first hooking the cable to the side of the dishwasher. The other end of the cable assembly with two holes hooks up to the two large springs which keeps the door in balance. Hook one spring at a time to the cable assembly.
Reassemble the two bottom panels with the four screws.
YOU ARE DONE - Congratulations, you just saved $125 which is what the plumber quoted me.
Replace the broken cable by first hooking the cable to the side of the dishwasher. The other end of the cable assembly with two holes hooks up to the two large springs which keeps the door in balance. Hook one spring at a time to the cable assembly.
Reassemble the two bottom panels with the four screws.
YOU ARE DONE - Congratulations, you just saved $125 which is what the plumber quoted me.
Was this instruction helpful to you?
Thank you for voting!
door seal leaked,and the baffles
removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you
Was this instruction helpful to you?
Thank you for voting!
broken door spring cable and missing lower rack wheel
Part delivered in 3 days
1. remove kick panel (4 screws) - remove broken cable - install new cable - reinstall kick panel - done.
2. snap retainer hub into wheel - snap retainer onto rack - done.
1. remove kick panel (4 screws) - remove broken cable - install new cable - reinstall kick panel - done.
2. snap retainer hub into wheel - snap retainer onto rack - done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from TUCSON, AZ
- Parts Used:
- WD35X10346
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
threads were faulty
Removed the 7 screws from inner side of door; removed set screw from handle; removed inner door cover; pulled old part out; pushed new part in and Voila! Replaced all screws, no problem. Thanks for your great customer service!
Was this instruction helpful to you?
Thank you for voting!