40400118 General Electric Dishwasher - Instructions

Pulled out the top tray fully, popped off the end caps. Removed the tray and placed it on the cabinet top. Popped off the old rollers and snapped on the new rollers. Replaced the tray into the dishwasher, Popped the end caps back on and I was done.

Watched the video and swapped out the parts when they came. One of the arms that one of the rollers attached to was rusted and swollen had to remove the plastic coating and sand in order to get a good roller fit. Went super easy

Super-easy and quick repair -- quality part snapped right into place.

I have to be honest. At first I called a repair person, but it was Sunday so he couldn't come till the following week. Then my incredibly intelligent, industrious, and internet-savvy wife found your website. We saw that others had had the same problem. The part we needed was right there.... voila! 2 days later I had the part in hand. Not being the most handy of handymen, I followed the directions that others who had the same problem had posted. Yep, it was that simple -- And a heck of a lot cheaper than a repair person. Your website was very valuable, and I definitely will refer it to others looking for a part for a home repair job.

Removed access panel (2 screws), Replaced broken cable/Eyelet assembly. Replaced access panel. Job took 5 minutes, including clean-up & stowing tools.

My GE dishwasher had a problem. The upper rack would fall into the lower rack when loaded breaking dishes! Turns out, the front rollers on the upper rack were broken so that the supports would just pull out. So, I found the parts on this website easily. I then took off the plastic plug on the support which is easy to do. There is a flange you bend towards the rear of the dishwasher to release the plug. Once released you have access to the rollers, which just snap off easily. The new ones snap on easily. Reverse the cap removal, and you are done!

First, remove the two access panels to the bottom of the dishwasher, each had two screws. Then, disconnect each old door cable and eyelet assembly, and the two springs. Now, connect the two new cable assemblies, and reconnect the two springs, one at a time, between the eyelets of the cable assemblies. Finally, replace the access panels

Part delivered in 3 days

1. remove kick panel (4 screws) - remove broken cable - install new cable - reinstall kick panel - done.

2. snap retainer hub into wheel - snap retainer onto rack - done.

The cable attachment comes with the two hole loop assembly that the springs hook into. With the lower panel off and the door closed, the other end of the cable assembly hooks onto the fitting on the side of the door. No tools required except the phillips head screw driver to take off the lower panel.

Remove the bottom two panels below the dishwasher door. There are two phillips screws and two nut screws.

Replace the broken cable by first hooking the cable to the side of the dishwasher. The other end of the cable assembly with two holes hooks up to the two large springs which keeps the door in balance. Hook one spring at a time to the cable assembly.

Reassemble the two bottom panels with the four screws.

YOU ARE DONE - Congratulations, you just saved $125 which is what the plumber quoted me.

removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you

I followed the video instructions on removing the rack slide end cap to prevent breaking it and it was very easy to remove and replace the broken one. I attached the new rack rollers and voila we were back in business. I was about to order a new dishwasher the night before for $5oo! Thankfully the stores website wasn't working so I couldn't. I decided to look online to find out if it was easy just to replace the parts. Looks like I saved close to $500 just replacing those parts! AWESOME!!!!!Thank you for a user friendly website. It made all the difference")

Removed the 7 screws from inner side of door; removed set screw from handle; removed inner door cover; pulled old part out; pushed new part in and Voila! Replaced all screws, no problem. Thanks for your great customer service!

Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.

Took out old one and put in the new one. Not hard at all. Thanks