40400118 General Electric Dishwasher - Instructions

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

The repair was as simple as it could be. The real story is being able to find and replace the missing wheels. Your website makes it real simple to find the proper parts, order them and receive them in a few days. Your parts person; Jason was very nice to send me a little note concerning my order. I appreciate that personal touch. I will be a regular customer with that kind of service. Well done/Good Job.
Bill

My suggestion is to replace all four rollers at the same time since they are all the same age. Fortunately, four rollers come in each pack you order. You need to remove the end cap on borh metal rack rods which takes a little doing. You cannot just pull the caps off. You need to twist the end cap to free up the little catch at the rear of the end cap. Once the end caps are off, just pull of the old rollers and install the new ones, replace the end caps and you're done.

First I removed the four screws holding on two metal panels to gain access to the springs. Then I unhooked the broken assembly from the springs. Then I hooked the new assembly to the hinge. Finally, I reconnected the assembly to the springs. (I didn't have to unhook the assembly from the hinge because it had already broken off.)

This part must be one of those that commonly goes because I had replaced the other side about a year ago. The most difficult part a year ago was diagnosing the problem and figuring out how the pieces fit together. This now it was a quick repair because I knew exactly how to fix it. (And thanks to PartSelect for delivering the part in 48 hours even though I didn't pay for quick delivery.)

The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.

installed new rollers per diagram then installed side ends into sides. Couldn`t have been easier. Dishwasher is like new now.

took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!

Pulled the lower left side end of the old door gasket out of door gasket retaining slot and slowly and evenly continued to work my way around the door pulling the door gasket out of the retaining slot until I reached the end. I installed the new gasket into retaining the retaining slot beginning on lower left side and then slowly and evenly working my way around the door inserting the new gasket into the retaining slot. I was careful to make sure the two cutout portions of the new gasket's retaining edge were correctly positioned in the lower corners of the door.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.