GSD4310X01BB General Electric Dishwasher - Instructions

Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Put on a new cap.

I used Partselect.com to bring up my model #. Partselect.com provided complete breakdown of the part and where it was located. It was very easy following the diagrams provided.

over time the upper rack axles broke so the rack would just come out of the rollers. I ordered the parts from here and had to youtube how to get the stops out so I didn't have to unscrew the metal guides out making an easy job into a hard one. all you have to do is with a flat head screw driver is slightly bend the plastic end part of the stop which is in the metal guide that stops the wheels from coming out of the guides. once you bend out the plastic end you then turn the stop to get it out of the metal guides. if you youtube it its very easy. just be easy when you bend the plastic piece because I can see it breaking. I didn't break mine so the job was very very easy and took all of about 5 to 10 minutes to complete the entire job. I love this site it had real life info to help out when you need to do a job and trouble shoot your appliance.

Determined not to call a repairman for such a simple problem, I watched your extremely helpful video. The ordered parts came right away and all it took was a screw driver and 30 minutes to take off and replace four rollers. So easy, this 75 year-old grandma could do it!

The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.

Pop the end caps off the slides by pushing the lock tab in with a medium flat screwdriver, through the square hole in the side of the slide. Pull the rack out and set it on the counter. Pop the axles off, with the rollers, with your fingers. They are just clipped on to the rack wire. Pop the new ones on 4 places, fingers only needed to clip them to the wire. Put the rack back in the dishwasher by aligning the rollers in the metal slides and pushing it in like normal. Pop the rack slide end caps in by just pushing them in. If you're smart you bought new ones, they're cheap insurance. Save any good used parts in your kitchen junk drawer for the next time you treat it rough. Less than 5 minutes to fix. So easy a caveman could do it. One just did!

Looked up possible causes on your website. Website stated that more than 50% of time the cause was the piston and nut assembly. Removed the piston and nut assembly in bottom of unit behind screen on rear wall and saw that the gasket seal was completely gone . Ordered the part. took less than 10 minutes to install. Tested the unit and it drained completely. Thank you as i was looking at a more difficult repair if the pump had to be replaced.Repair cost less than $20.00.Before changing piston and nut assembly I cleaned the strainer and sump. disconnected drain hose and checked for blockage . i than checked your website that listed the piston assembly as the culprit more than 50% of the time. Thanks again

Snapped right in

installed new rollers per diagram then installed side ends into sides. Couldn`t have been easier. Dishwasher is like new now.

The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.

According to instructions with part

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

easiest way i found to do it was pull dishwashers out from under the cabnet... laided a pillow down in front of the door and turned it on the front side... the part was very easy to get to at this angle....could have done it in less then 5 minutes but took my time to double check everything to be safe....took a total of about 10 minutes..... very happy now no longer need to vacume out the old dish water left at the bottom of the dishwasher...... i think most anyone could do this very easy....