GSD4310X01BB General Electric Dishwasher - Instructions

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.

Use screw driver for leveage, righty tighty, lefty loosie, easy as that, and thanks to Parts Select, ordered my part on Thursday by dinner time Friday had part, install no washing dishies by hand, Thanks guys

Brian Souza
Vacaville, CA

Simply screwed in new cap

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

I had already removed the screws that hold the inner door piece in place when diagnosing the problem. I snapped the new controller in place, put the 3 or so screws back in that hold it to the door, and replugged the wire harness connections from the power and the Sequencer. I put the inner piece of the door in place and replaced those 5 or so screws and restored power from the breaker box. The dishwasher gave a solid beep while the clean light flashed continuously. No other buttons were responsive and pressing the reset button caused a beep but nothing else. I began to research and diagnose that problem which was leading me to the Sequencer when I realized there was a "rewiring" plug on the controller I replaced that was not on the new controller. The controller which is made by Torisan is a generic part used by many manufacturers. The "rewiring" plug which goes into slot CN5 on the controller circuit card, which has wires that comes out of it and go back into other slots in the plug, is used to get the get the correct "pinout" sequence for GE's use of this generic component. Although I could find no information on this, the continuous beep was telling me there was a wiring problem. I removed the plug from the old controller, put it in CN5 of the new controller and the dishwasher works like a charm.

Took inner door panel off and cleaned and replaced gasket.

First, I drained the water from inside the washer and removed it from under the sink. I wasn't sure if I had a clog in the drain line, so I dissasembled the drain under the sink and cleaned that as well. While cleaning under the sink my wife found her $4000 dollar ruby that fell out of her mothers ring a couple weeks earlier. It must have dripped out of the trap while I had water draining everywhere. Put drain back together and moved on to the dishwasher repair. Parts were easy to install after laying the dishwasher down on its front to access the bottom back side. Hooked everything back up and slid it back under the countertop and away it went. Had one small leak after running (water in line wasn't tight enough). A twist with a pair of pliers and that was resolved.
Fast shipping by the way! I paid a little more for the exit washer than I wanted to, but with shipping only from one source and delivery of parts at the same time made downtime as little as possible. I'm sure I saved $100 dollars or so by using this website for parts and tech info. And recovered a precious stone to boot.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

stripped old gasket from around the door (easy part)

instructions said to remove two screws from the bottom of the door to allow you to fit the gasket around the bottom

this was not too easy as you cannot get see the inside of bottom end of the door
I ended up removing the other door screws and this allowed me to fit the gasket quite easily

one tip tape the door lock immediately after removing screws as the lock assembly is not attached to the door

final step was to make sure the gasket was seated all around as my first wash had a slight lead

by pushing on the door after the door was locked cured the problem

Very simple. By hand, I unscrewed the old spray arm and screwed in the new one. One brief hangup. The old spray arm was very hard to unscrew. Rather than seeming to force it, I called the PartsSelect 800 number and got advice. The tech reassured me that all I had to to was unscrew it and put in new one. So I applied more force and old one came out. A breeze.

Quick and easy!! I am not a good repair person, but this was about as easy as it gets. Take off the old put on the new. Make sure that you have it equal on both side of door before you put your gasket in. Just so you dont have to do it twice.

Each replacement wheel came in two parts: the wheel itself and the clip which had to be pushed through the center hole in the wheel in order to attach each wheel to the carriage that holds dishes. I had difficulty assembling the clips and wheels until I ran the clips under hot water to soften them. This made it possible to assemble the wheels and attach them to the dish carriage. I would have preferred the wheels to have come assembled, particularly given the price of each one.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

After reading about this problem on an appliance repair forum, I learned that it is usually caused by a faulty piston valve. The valve is located under the rear screen filter and can be removed with your fingers. The parts arrived very quickly and we saved $$$ by not having to pay for a service tech visit and "mark-up" on the replacement parts.