4070510 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Estelle from Queen Creek, AZ
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a rip in our tub gasket.
I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from LOUISVILLE, KY
- Parts Used:
- WD28X10384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishrack was worn and causing chips on dishes
just slid the new rack into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Hudson, FL
- Parts Used:
- WD21X10247
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
main control board malfunction
Diassembled the door from the insside and installed new board as instructions specified.
Frustration is that this is the second time I have had to replace for the same dishwasher....
Frustration is that this is the second time I have had to replace for the same dishwasher....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maurice, LA
- Parts Used:
- WD22X10084, WD22X10047, WD22X10046, WD12X10109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishes where not clean after washing
change the nozzles and filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Clinton township, MI
- Parts Used:
- WD13X10045, WR02X10585
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch broke
took off eight philips screws on inside door panel which then exposed the broken actuator and missing spring. Replaced broken and lost parts and reset actuator in door then reinstalled inside door panel. Done and I'm happy not to have called service.
Joe
Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MACKINAW, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from North Las Vegas, NV
- Parts Used:
- WD28X10399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Top rack had the plastic coating coming off
Had to replace the top rack in the dishwasher. Removing the top rack was a tricky. Have to push the tab out not in on the stopper ends of the rack. Unscrew the bolts on the water sprayer. Need to slide the sprayer instead of unclipping it. Real easy to do once it is realized. Should have taken 30 minutes if I knew this in advance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ARTHUR from OAK PARK, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Detergent dispenser did not work
Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN D. from GOSHEN, IN
- Parts Used:
- WD01X10175
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
wouldn't drain
Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TUCKAHOE, NY
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from FREDERICKSBRG, VA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHNNY from FORT WORTH, TX
- Parts Used:
- WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
frost build up
flapper then bought the spring
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C. from Lexington, KY
- Parts Used:
- WD01X10175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would only drain intermittenly
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Harrison, AR
- Parts Used:
- WD21X10247
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Unit would not turn on
Changed the main chip. the unit then started and continuously ran. Thought something was wrong with it. It is just a cycle of the dishwasher and when the pump quit running the dishwasher ran and operates. Saved me lots of money and time.
Was this instruction helpful to you?
Thank you for voting!