4070510 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christopher from GLEN ALLEN, VA
- Parts Used:
- WD05X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Dishes were not drying inside the dishwasher after the dishwasher cycle completed
The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Terra Ceia, FL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
The water valve went out
I took the old one off and replaced it with the new one, which fir perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from HAYMARKET, VA
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaked front right side
Followed the instructions that came with the my order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARIA from DETROIT, MI
- Parts Used:
- WD08X10059, WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leaking door
changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Sykesville, MD
- Parts Used:
- WD28X10177
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
basket for silverware was broken
opened the box , new one was an exact fit, pulled out the old one and dropped the new one in place??, this is more of a review, the new part was the exact same one...perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessie from TYLER, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Jet dry rinse cape destroyed.
Got the part the next day.. opened it and just screwed into place!
Easy as could be. Thank you!!
Easy as could be. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irma from Smyrna, GA
- Parts Used:
- WD35X21035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Upper Rack Wheel and Stud Assembly
I removed top dishwasher rack, popped off broken studs, and removed wheels from the tracks. I replaced studs on rack by popping them into place, and I slid new wheels back into wheel tracks. I place new studs into wheel assembly, slid rack back into dishwasher and replaced stoppers at the front of the tracks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MarilynNegri from BLAIRSTOWN, NJ
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap to rinse aid disoenser
Just screwed it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURKBURNETT, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rinse aid cap leaking
Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Bakersfield, CA
- Parts Used:
- WD22X10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Broken middle spray arm
Unscrewed the screw holding it in place and removed it, out the new one in place and screwed it on. Very quick and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from North Charleston, SC
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking from front
I removed the old gasket very easily as there wasn't even glue holding it in place. The new gasket just pressed right into a slot and makes a water tight seal.
Was this instruction helpful to you?
Thank you for voting!