PDT750SSF7SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Al from HILTON HEAD, SC
- Parts Used:
- WD12X20118
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Right part wrong description
I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.
I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.
Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.
I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.
Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from RIVERVIEW, MI
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Dishwasher ceased to fully drain after full cycle
First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!
Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from AUGUSTA, GA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Heating Coil was inoperable
My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and checked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.
Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.
The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.
However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.
Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...
Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.
The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.
However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.
Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CARY, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
No boost in water temperature; water temperature during wash cycle not hot enough; dishes not drying
Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emilene from BRENTWOOD, CA
- Parts Used:
- WD28X20163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine on lower rack broke
Just snapped it in place and that’s it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DANBURY, CT
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ge Dishwasher was not filling with water
I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from WILMINGTON, NC
- Parts Used:
- WD09X21321
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken Dishwasher Door Handle
I followed You-tube instructions, very clear but not easy.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
Was this instruction helpful to you?
Thank you for voting!