GSD2800D01 General Electric Dishwasher - Instructions

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!

Removed screws on the drain pump filter screens at the back of the dishwasher, unscrewed the check valve, screwed in the replacement unit, and re-affixed the filter screens.

I lived with the drain problem for 6 months and reviewed on line trouble shooting which all pointed me to a pump or solenoid valve problem. I pulled the unit and disassembled everything before noticing that the rubber washer/stopper at the top of the check valve had erroded away and was not preventing water from pumping back into the cabinet when the drain pump kicked on. Always check the condition of this check valve first if you dishwasher is not draining properly. It was so easy once I found the bad part.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

The dishwasher was in a rental so I didn't want to spend the money for a new one. The part was expensive compared to a new (cheap) dishwasher. The order was shipped promptly and arrived when I expected even though it was Christmas time. The part fit perfectly and everything is back in place.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

Super-easy and quick repair -- quality part snapped right into place.

There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.

removed relay and replaced, found moth cacoon inside relay. Goodman a/c not3m no goodman in list

Door seal was brittle and flat.
Not a hard job to do just having to keep making sure the seal did not pop out on the bottom corners of the door. The seal would tare easy so have to be careful. Before you remove the old seal on the bottom of door there is a 4 inch space between the ends of the seal. Mark the spot with marker so you know where to start placing the new seal.
Baffles were orginaly put in place with plummer putty, do not use this. Get GE clear seal is the best will hold forever but will come loose with a good tug. easy to clean out when replacing baffles again. Do not use any sealent when inserting the door seal just push into opening. Make sure you support the door when pushing down on door to put the seal in the slots.
The hardest part is the bottom corners the seal tends to slip out I found that if I streached the seal over the openings and continued on and come back to the corners it was easier to make the seal slip in.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.