PDT720SSH7SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Erland from SAINT PAUL, MN
- Parts Used:
- WD28X20163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two tines broke off the original divider in the bottom rack
The part is held in with two plastic clips, which are easy to unclip. The part needed to be slightly flexed to release it and the new part went in the same way the old one came off. One issue: The replacement part had one extra row of tines that encroached on the silverware basket. As it turned out, one tine fit between basket sections and the other fit through the hole in the bottom of the basket and it doesn't interfere with utensils so it turned out not to be a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CARY, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
No boost in water temperature; water temperature during wash cycle not hot enough; dishes not drying
Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from SCHENECTADY, NY
- Parts Used:
- WD05X30818, WD21X10519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
No heat in both water and air
Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Downingtown, PA
- Parts Used:
- WD05X30818, WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Doesn't complete dry cycle, no clean light, random noises as if door was closing
After replacing UI board, I replaced the mainboard. still did not solve the problem. The element tested good and I had removed the flood switch, rinsed and blew it out so it rattled but the damage was done. Replacing it made the dishwasher heat water and heated during dry cycle. Removed fine filter, removed course filter, removed two screws with nut driver, removed flood sensor and then reversed. A year or so ago, the dishwasher flooded for no apparent reason, wondering if that was the beginning end of the switch!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from STERLING, CO
- Parts Used:
- WD05X30818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher was not drying
I followed the U tube instructions already put out part select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emilene from BRENTWOOD, CA
- Parts Used:
- WD28X20163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine on lower rack broke
Just snapped it in place and that’s it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from WILMINGTON, NC
- Parts Used:
- WD09X21321
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken Dishwasher Door Handle
I followed You-tube instructions, very clear but not easy.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- louis from FRANKFORD, DE
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
dishes were not dry at end of completed wash cycle
Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DANBURY, CT
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ge Dishwasher was not filling with water
I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from CONCORD, NH
- Parts Used:
- WD05X30818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher was not heating up to dry
Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
Was this instruction helpful to you?
Thank you for voting!