GSC3430ZZ0WW General Electric Dishwasher - Instructions

The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.

remove bottom tray and rear cover from inside washer.then remove PISTON NUT ASSEMBLY CHECH VALVE by turning it to the left. replaced with new valve assemmbly. IT IS workng like NEW.TOOK ME 30 minutes.VERY EASY!!!!!!!!!!thankyou allfor the help.

ordered and received parts. unplugged electricity and drain and water supply turned dishwaser upside down for ease of access. removed clamps usin 1/4 and 5/16 nut drivers and phillips head screw driver to undo bracket clamps old parts and replaced and as per directions using two pair of adjustable pliers one to hold motor shaft and other pair to remove cutting blade. replaced impeller and blade ttaking care to keep track of screws nuts and bolts and older parts to make sure of assembly. turning dishwasher upside down makes for easy parts instalment. PAY CLOSE ATTENTION TO DISASEMBLY AND PUT TOGETHER IN REVERSE ORDER GOOD LUCK parts ordered to replace solonoid kit as it feels hot and still have burning bakelite odor.

Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.

I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under the cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.

I went to your site and check all the diagrams and then read the postings from others. I turned off the electrical breaker then took off the lower cover of the dishwasher. After disconnecting the water and electricial connections I was able to remove the 2 screws holding the unit in place and it came right out. I turned the unit over and was able to just remove the old part and put the new part in place. The whole job took me about one hour but I had never worked on a dishwasher before. Your site made the repair very easy to do on my own.

Took off little white plastic pieces at end of rail. Old rack off and new rack on. End pieces in and railing tighten with pliers. Easy!!!

Just remove the 4 screws at the lower rear inside the washer to remove screen holder...then unscrew the Piston and Nut Assembly by hand. Put in the new unit, reattach the screen holder with the 4 screws...and the job is done. Probably takes less than 5 minutes....very easy.

The finished accent panel on my GE dishwasher was dented and looked awful in my newly remodeled kitchen. I thought about purchasing a new dishwasher but instead searched the web for the part. Found Parts select and it was so easy to compare my part with the graph picture provided. Just count off the boxes for measurement and you will know if you selected the part you need. Access panel arrived in two days,packaged well, and I am happy to have found this website. Give it a try....and returns are easy too if you make a mistake in ordering. My order was perfect on the firt try.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

I pulled the two clips in the rack guides and pulled out rack and reinstalled the new rack and put the clip back in the rack guides

Thanks for your prompt shipment of the rack I ordered

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.