GLD4464R10SS General Electric Dishwasher - Instructions

UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS

Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.

It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!

Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found

Slid it in. Very easy and the replacement part is built better than the original part.

Took old basket out and dropped new one in .

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

Installed new lower rack wheel kit

Just screwed it on.

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.

I first watched a video on trouble shooting on You Tube. I took the insides of the dishwasher apart and found broken glass and some other debris.I shop vacuumed the inside and the dishwasher pump put back together and ran a rinse cycle,unfortunatly dishwasher was not draining. Got the model number and ordered the dishwasher pump through Part select. Within in a few days I had the part in hand and had to remove the dishwasher from under counter. Once turned over the pump was right there ands took 5 minutes to change replaced pump put everything back together and now dishwasher drains as expected.

changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.

Removed two upper rack rail end cap stops. Removed upper rack. Replaced four old upper rack rollers (wheels) and installed four new upper rack rollers. Replaced upper rack in correct position. Installed two new upper rack rail end cap stops. The new end caps were different from the old ones, and the new wheels had shorter retaining arms than the old ones. Once observing the differences, the new parts fit properly and perfectly.