GLD4464R10SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from THE VILLAGES, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels on the lower rack of our dishwasher kept falling off.
Removed the lower rack. Took off the old wheels. Put the axles on the new wheels which took a little manpower, but became easier once you did a couple (there are 8 wheels). Then snapped the new wheels on the rack which was really simple. The new design is much improved to the old one. The wheels glide better, then they ever did. We're sorry we didn't think of this repair years ago and the cost was a fraction of the cost of a new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harinder from CHESTERFIELD, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispenser was not closing and dishes were dirty
followed the video step by step which was very well expalined and was able to complete the install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from JONESBOROUGH, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Would not fill with water
Ordered most likely part...water inlet valve.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from NAPLES, FL
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from royal oak, MI
- Parts Used:
- WD12X10401
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
a couple of retaining ears were broken from the cover allowing the the switches and plunger to move out of place
took screws from inside door panel and replaced the cover taking care not to allow plunger and spring to pop out put panel in place and screwed down
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cincinnati, OH
- Parts Used:
- WD35X21038, WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack roller and JetDry cap were missing
Opened the package, opened the plastic parts bag, installed the roller and the cap.
Whew!
Whew!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Blairs, VA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken off end caps, top would slide off, frustrating.
did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Jacksonville, FL
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front door on Dishwasher Leaking
Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from PALMER, MA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessie from TYLER, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Jet dry rinse cape destroyed.
Got the part the next day.. opened it and just screwed into place!
Easy as could be. Thank you!!
Easy as could be. Thank you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laverne from Roselle, IL
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pieces that attach the wheels to the lower rack kept falling off
Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Fitchburg, WI
- Parts Used:
- WD12X10304, WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
End Cap and Wheel axle were worn or broken
This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.
Thanks for the quick delivery and great website!
Thanks for the quick delivery and great website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from North Charleston, SC
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking from front
I removed the old gasket very easily as there wasn't even glue holding it in place. The new gasket just pressed right into a slot and makes a water tight seal.
Was this instruction helpful to you?
Thank you for voting!