GSC3430Z03WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Livermore, CA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Pump valve leaking
I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Holiday Island, AR
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
motor noise.
Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Rumney, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak
Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Pinehurst, NC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water would not drain
Replaced the Piston and Nut Assembly, located inside the dishwasher under the screen at the back, by unscrewing the old one and replacing with the new - Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Franklin, MA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Dishwasher didn't drain
Assistant helped me take apart unit, assumption on issue was correct, part was ordered and showed up 3days later. I installed and all seems fine. I do question what would have happened if the deduction was incorrect. The assistant was very patient and clear with his instructions. A good experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WD28X10232
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken tower
removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lakeport, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked riser in spray arm
Ordered part Monday evening installed it on Wednesday afternoon. Required a pair of pump pliers to loosen old part, new part screwed in by hand. No leaks, no problems. Took longer to explain what caused the problem then it did to fix it. I explained to the owner that overloading the dishwasher was most likely the cause. Dishes can move or fall against the riser during wash, preventing it from dropping back down. Pulling the lower rack out with the riser bound up caused the part to crack. Thanks for the speedy delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hopatcong, NJ
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher not draining completely
This was a piece of cake! Simply removed the rear drain cover with a nut driver and unscrewed the piston from its seat. I noted that the seal in the old piston had deteriorated over time. I rubbed a little petroleum jelly on the upper gasket of the new piston and simply screwed it into place, solving the problem entirely. Could not believe how quickly the part was delivered - next day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from woodbridge, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Water would not drain after cycle
After reading some of the suggestions I couldnt beleive it was that simple and easy. So I ordered the piston and nut assembly, installed it in less than 15 min. and after a rinse cycle test the problem was fixed. Thank you all for this wonderful site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Summerville, SC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher would not drain
Logged on to this site. Removed 4 nuts at the very back. Removed the piston & nut assembly. The rubber piece had worn out. Reversed the process and it runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Kingman, AZ
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Dishwasher was not draining
I removed the basket in the back of the dishwasher and unscrewed the plastic piece under the basket. I quickly screwed in the new one and now my dishwashe ris working perfectly.. We came so close to buying a new dishwasher and I am so happy I found the website describing this part. THANK YOU!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Om Prakash from Highlands Ranch, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pool of water at the bottom of the dishwasher after the cycle is complete
It is so easy and simple! Just removed the old part ( Piston and nut assembly), which is at the back of the dishwasher(inside, behind the spray arm and the heating coil) with bare hands. It needs a little push and turn , just like you removing a old stuck nut. One you remove the old nut assembly, replace it with new one. Just hand tightened is enough. Ran the dishwasher and voila...it works like a new one. No more water collection at the bottom! All it took is 10 mins + 12 dollar part + 7 dollar shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hubbard, TX
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
would not clean the dishes
I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Courtney from Lancaster, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher not completely draining
Followed the video on the website - seriously easy. took me 5 minutes and solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Yucca Valley, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The smallest portion of the sprayer had been broken
Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!
Was this instruction helpful to you?
Thank you for voting!