GHDA350N10BB General Electric Dishwasher - Instructions

My son took the part and it plop right into place with a click, and we were able to use are dishwasher again,Thanks

I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.

In order to replace the upper dishwasher rack I needed to remove the end stoppers on the sliders. They were difficult to remove and one of them broke. I then ordered new end pieces. The new ones had been redesigned and were very easy to insert. If you need to replace the upper rack be certain to order new endpieces along with the order for a new rack. They are quite inexpensive.

First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.

Took lower panel off with screwdriver. Removed old spring. Attached new spring. Very easy, and I'm a woman. LOL

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

Check website, order part. Hardest part was determining which was the right part. Needed the axle--I call it the hanger. I had previously called and ordered, but only received the wheel with no way to attach it. Push the axle into the wheel. Push the axle onto the rack. Since it was new, it didn't slip right on, and had to push it hard. (However, when it snapped on, three of the other wheels and axles came off.) Had to put them back on as well. Much easier, as they were older and not as snug. Total time: Took longer to open the package than put it on.

Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...

On the front ,lower side of sprayer arm removed the 1/4" screw and you have to stick your head inside and look on the backside of the spayed arm. Locate the plastic clip and gently pry a little just enough to loosen it off the rest of the way, be careful not to break off. It came right off I popped on the new one replaced screw and rain a load of dishes. Thanks for your help and great products for us do it yourselfers.

After installing the part, ran the washer once more. The water still remains in the washer. Tried washing several times. The problem is still the same.

Disconnected power at circuit breaker, removed lower spray arm, fine filter, inlet cover, and sump cap - manually drained water from inlet sump, then laid dishwasher on its side. Removed motor/pump housing, collection chamber, and associated hoses from inlet sump and extracted inlet sump from inside the dishwasher. Reversed process to install new inlet sump, paying careful attention to ensure a leak-free repair. The problem was damage to the part of the inlet sump that receives the feed from the fine filter - the inlet sump material had been damaged when I tried to clear some debris, resulting in a less than perfect seal when the motor/pump reversed and attempted to push water out of the dishwasher. New inlet sump, perfect seal, all the pressure is now pushing water out of the dishwasher during the drain cycle. PartSelect diagnostic app and parts diagrams were instrumental in being able to repair the dishwasher for less than $25.00 versus a service call costing hundreds. Thank you.

I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.

Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.