GHDA350N10BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from Loving, NM
- Parts Used:
- WD26X10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher pump was frozen
Ordered pump mechanism and replaced defective pump. A very easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Fair Oaks Ranch, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom shelf would not roll properly
so easy! Ordered the rollers and clips ... popped them on and done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from mashpee, MA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom basket of dishwasher kept following out
i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R. Cecil from Norfolk, VA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel was distorted
Simply replace wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Sun City West, AZ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaks
All new seals
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from easton, PA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher door switch
unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Naples, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not switch on whenon/off lever was pulled accross
Switch off the circuit breaker supplying power to the dishwasher.
Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.
Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.
Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.
Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.
Snap the switch (or switches) back into place in the cradle.
Replace the spring activator along with the plastic sheeting and screw that back in.
Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.
Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.
Switch the circuit breaker back on and give it a whirl. Enjoy!
Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.
Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.
Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.
Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.
Snap the switch (or switches) back into place in the cradle.
Replace the spring activator along with the plastic sheeting and screw that back in.
Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.
Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.
Switch the circuit breaker back on and give it a whirl. Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Nappanee, IN
- Parts Used:
- WD09X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the timer knob
Pushed the new timer knob in the hole, snap, job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from BOYNTON BEACH, FL
- Parts Used:
- WD28X31818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rusted out upper rack needed replacement
using small flat head screwdriver popped off clips at end of runners --rolled in new rack-- inserted clips back into runners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Waterford, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bad wheel
Pull rack out put wheel on put rack back
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith W. from Topeka, KS
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rear rack wheels
Quick and easy...a 7 yr old could have done it.
Was this instruction helpful to you?
Thank you for voting!