GDWT306V00BB General Electric Dishwasher - Instructions

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

Replaced impeller

I simply removed the bad part and reversed the process. It was very easy and a 12 year old could do it. Thanks for the online tips and recommendations. You saved me over 400.00 which is what a new unit would run. Plus installation. Many Thanks.

Simple as 1,2,3.Parts on time and priced right.

It was an install. My problem is that the drain tube is not standard to other dishwashers,so I could not get it at either of the local home improvement centers. The good news is that it is larger than the standard, and offers better discharge.

Replaced the original roller connectors with newly designed connectors. Works much better.

I ordered wheels on this wonderful site that looked like they made more sense and replaced all eight on my dishwasher and FINALLY the dishwasher isn't the nightmare it has been. It took seconds to pop in the clip to the roller and pop it on the rack. Thank you PartsSelect

Used plier to pinch the axle head to take the old wheels off then pushed the new wheels on by hand.

Remove all wheels on one side. Use pliers to remove broken axles from wheels. Pop in new axles, then go to lower rack and attach to rack by pushing axle pinch mechanism onto rack support. New axles do not look like old ones—they are improved.

Ordered on a Friday and parts arrived Sat. No tools required. Pieces easily slipped into place. Dishwasher is all fixed. This site is much easier to use than GE's. Will use PartSelect for all future replacement parts.

So easy and the posts on the site were incredibly helpful in determing what part i needed. The wheels on the dish rack inside the dishwasher kept falling off. I had to keep lifting the dish rack in and out of the dish washer to load and unload it. Unbelievably annoying. I popped the old wheel axels out of the exisiting wheels and replaced them with the new wheel axels I ordered from PartSelect. Then I attached the wheels back on the dish rack and it was right back to normal.

Very easy job. Just took out the bottom rack and replaced the wheels that kept falling off. A no brainer! works wonderful now. Most impressed with the ease of ordering and amazed how quickly the parts were delivered to me. I saved alot of money doing it myself! Thnak you

We ordered 4 wheels and axels, took off the old wheels, assembled the new wheels by popping the axel into the wheel (really simple) and then snapping them onto the post. It was incredibly simple. We waited 3 days for the wheels to arrive,the mailing cost was more than the parts! The result is amazing, the lower rack now runs smoothly and sits inside the washer as it should do without falling down all the time. Well worth the small amount of effort to find the right part and much cheaper than buying a new one!