ZBD3500ZZ0WW General Electric Dishwasher - Instructions

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix

Piece of cake. All done and working just fine.

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

First I removed the four screws from the screen/cover located at the back of the dishwasher. You will notice a mesh screen in the center of this cover. The check valve is under this cover midway between the sides. The check valve is unscrewed counter clockwise. I had to use a pair of pliers to start turning the valve. There are two "ears" on the top of the valve. You will see a rubber cone shaped piece that should completely cover the opening when the plunger is depressed. In my case the rubber was almost completely gone allowing water in the drain hose to return to the dishwasher after the drain pump stopped. The new check valve threads back into the opening and should be finger tightened. Replace the cover/screen and you should be good to go.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

removed piston in filter and replaced. the check valve had come apart and was not sealing

Replaced the Piston and Nut Assembly, located inside the dishwasher under the screen at the back, by unscrewing the old one and replacing with the new - Works great now!!

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

Assistant helped me take apart unit, assumption on issue was correct, part was ordered and showed up 3days later. I installed and all seems fine. I do question what would have happened if the deduction was incorrect. The assistant was very patient and clear with his instructions. A good experience!

removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.

After reading some of the suggestions I couldnt beleive it was that simple and easy. So I ordered the piston and nut assembly, installed it in less than 15 min. and after a rinse cycle test the problem was fixed. Thank you all for this wonderful site.

Logged on to this site. Removed 4 nuts at the very back. Removed the piston & nut assembly. The rubber piece had worn out. Reversed the process and it runs like new.