GSD5910F00AA General Electric Dishwasher - Instructions

My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.

Removed screws on the drain pump filter screens at the back of the dishwasher, unscrewed the check valve, screwed in the replacement unit, and re-affixed the filter screens.

I lived with the drain problem for 6 months and reviewed on line trouble shooting which all pointed me to a pump or solenoid valve problem. I pulled the unit and disassembled everything before noticing that the rubber washer/stopper at the top of the check valve had erroded away and was not preventing water from pumping back into the cabinet when the drain pump kicked on. Always check the condition of this check valve first if you dishwasher is not draining properly. It was so easy once I found the bad part.

and there was not supposed to be so I checked the drain and it was clean and I found a part in the back that looked like it was damaged from use and it was so I got a new part and changed it and that fixed the problem. I removed the screen from the bottom rear inside the cabinet that covers the nut and piston and I changed the part and that fixed the problem . Now no water stays in the bottom when the cycle is done.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Repaired by watching the video provided on my computer by this site . This video was a life saver and covered every detail. My thanks to this site !!!

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.

I took the inside of door off to install both gasket and gasket insert. Much easier this way. Also it’s much easier to fish locking handle through the door if you extend the handle half way and put through opening when raising the door.

I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

I removed the two screw at the top holding the dishwasher to the counter top; pulled on the unit - but found it stuck on something.
Of course the hot water feed and the drain hose were still connected and would not let the unit move out any further as there was no slack.
If I had thought about it - I would have disconnected these from under the adjacent sink. But I ended up lying on the floor trying to disconnect them from underneath the unit. It was a bit difficult as there was very little room to move the wrench and the screwdriver.
Once done, the unit came out very easily.
When tipped over I disconnected the old motor and replaced with the new. It was a very different design but fitted in very easily. The hanger took a bit of working out as the diagrams are not very clear.
The wires and clips went together easily. Once I had cleaned everything around the motor and the gunge that cames from years or washing dishes, it went back the way it came out. Albeit with the same difficulty with feed and drain hose.
We ran the unit with no dishes for a couple of times to clear our the muck left in the pipes when the system was down.
Now we have a fully functioning dishwasher again. Cost $250 for the pump and motor as opposed to the $800+ unit my wife was looking at!