GSD5910F00AA General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Franz from Hazlet, NJ
- Parts Used:
- WD22X10017
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
How To Replace The Lower Spray Arm Assy.
First make sure the dishwaher is off and secure to work on: remove the lower basket, turn the broken spray arm assy counter clockwise, it may be tight, but no tool be need it, screw it all way out, remove it and replace it with your new one by turning clockwise,make sure its tight, no tools need it but basket in place and the dishwasher is ready to go
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ira from Fort Edward, NY
- Parts Used:
- WD02X22736, WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
Dishwasher was leaking
Disconnected the electrical, water supply and drain. Pulled unit out from under counter, tipped it on its side and replaced the motor/pump unit. tipped it back on its legs put it back under the counter connected the water supply, drain and electrical. All went well. The unit performs as it should. it took about two (2) hours without rushing through it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Springfield, VA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old roller wheels were starting to stick due to cracking
1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Hailey, ID
- Parts Used:
- WD24X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Stinky Dishwasher
I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.
Now my dishwasher doesn't stink anymore!
Now my dishwasher doesn't stink anymore!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Cedar Rapids, IA
- Parts Used:
- WD28X24469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Silverware Basket Broken
Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Salem, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace rinse aid fill cap
Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oria from Scottsdale, AZ
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rust
Just took the old rusty rack out and put the new one in its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Stony Point, NY
- Parts Used:
- WD18X214
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Water Leak In Rubber Connector Pin Hole At Seam
Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from ansonia, CT
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Old Lyme, CT
- Parts Used:
- WD12X10327, WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
2 rollers and end caps were broken were broken
Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lucas from pearland, TX
- Parts Used:
- WD24X214, WD24X10016, WD24X10006, WD18X215, WD18X202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
all rubber parts chewed
rat got in after hurricane and after eating poison chewed all the hoses looking for water. i thought about replacing the dishwasher but it was $1100 and for $109 i replaced all the rubber parts. it was a easy as looking at the parts on the chart and ordering what i needed. from there i used a screw driver, nut driver, and pliers to remove and replace parts, at first i was nervous about leaks because i am very weak in the plumbing department but to my surprise no gaskets, jellies, or putties needed it was a simple as plug and play.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Sparks, NV
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher wouldn't drain
Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from South Hadley, MA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dishrack getting rusty in spots
Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Quakertown, PA
- Parts Used:
- WD16X10011, WD16X313, WD16X297, WD35X10346
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Soap dispenser door wouldn't close
Replaced all ordered parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Columbia, SC
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
threads broke on rinse aid fill cap
Replaced with a new rinse aid fill cap.
Was this instruction helpful to you?
Thank you for voting!