GDF610PGJ6BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from LANESVILLE, IN
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Delivery
The part has been sitting at a FedEx place for over a week and no one answers my emails about why. This is all I get: "No scheduled delivery date available at this time."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BEND, OR
- Parts Used:
- WD28X22621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The blue colored silverware holders had broken pegs at the ends.
Removed the old assembly and put the new one in. Took about 15 seconds. Perfect replacement. This assembly is the complete basket. The color of the blue silverware holders changed to grey which is not an issue at all unless that was the reason you bought this dishwasher in the first place. ;-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from OAK RIDGE, NC
- Parts Used:
- WD35X10393
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher made rhythmic, thumping sound during wash cycle
This was so easy! Our 4 year-old dishwasher began making a repetitive, clunking noise during wash cycle, and I deducted that it was the spray arms. I tried to rinse out old
spray arms, checked for clogs, and made sure they were installed correctly. The sound persisted, so I ordered replacement part (wash arm kit). I removed old spray arms and attached new ones. Problem solved and dishwasher is quiet again!
spray arms, checked for clogs, and made sure they were installed correctly. The sound persisted, so I ordered replacement part (wash arm kit). I removed old spray arms and attached new ones. Problem solved and dishwasher is quiet again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plainfield, IL
- Parts Used:
- WD08X21894
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Worn bottom door seal
Easy repair, googled a how-to video and I was surprised how well i was able to follow instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from CONCORD, NH
- Parts Used:
- WD05X30818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher was not heating up to dry
Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from OXNARD, CA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bottom door seal broken and leaking
Unplug power to the dish washer.
Remove 2 kick plate screws to remove kick plate
Remove 2 screws that hold DW to underside of countertop
Slide out dishwasher enough to access the cables on each side at bottom of door.
With door closed, use plyers to lift the cable (one on each side) off the retaining stub.
Unplug door wiring connector.
Open door and slide door off the hinges.
Slide old seal out and insert new seal.
Reverse to reassemble
Remove 2 kick plate screws to remove kick plate
Remove 2 screws that hold DW to underside of countertop
Slide out dishwasher enough to access the cables on each side at bottom of door.
With door closed, use plyers to lift the cable (one on each side) off the retaining stub.
Unplug door wiring connector.
Open door and slide door off the hinges.
Slide old seal out and insert new seal.
Reverse to reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BURKE, VA
- Parts Used:
- WD08X21894
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher Leaking at bottom when running
To remove/install gasket one has to remove a Door Hinge Arm on one side. Then you can easy remove old gasket and replace. Please follow these steps when removing a hinge: https://www.youtube.com/watch?v=hTpe1dedyr8
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from PLYMOUTH, MA
- Parts Used:
- WD15X26140
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Dishwasher not operating. Would fill, not operate, then drain.
Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.
Was this instruction helpful to you?
Thank you for voting!