GDF610PGJ6BB General Electric Dishwasher - Instructions

The dishwasher rack was supposed to come with wheels it did not but I was able to use the existing wheels from the lower rack and snap them on was pretty easy

Followed instructions sent with wash arm kit replacement. Very easy.

2 hose clamps, connect the wire with the wire adaptor suppled

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

Pulled out old rack and replaced with new rack.

youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.

Opened the box took the rack out and placed it in the dishwasher. Good as new.

1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door

Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.

The only directions that came with the new pump and filter, was how to replace the filter. I had to find a You Tube video to show me where the drain pump was located., and the way to get to it. I also had to figure out how the new pump was hooked up electrically, since the new pump did not work with the plug in on the machine.

The part has been sitting at a FedEx place for over a week and no one answers my emails about why. This is all I get: "No scheduled delivery date available at this time."

Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

This was so easy! Our 4 year-old dishwasher began making a repetitive, clunking noise during wash cycle, and I deducted that it was the spray arms. I tried to rinse out old
spray arms, checked for clogs, and made sure they were installed correctly. The sound persisted, so I ordered replacement part (wash arm kit). I removed old spray arms and attached new ones. Problem solved and dishwasher is quiet again!