GDT655SGJ5BB General Electric Dishwasher - Instructions

Very easy repair. Remove wiring harness that is a simple click. Remove 2 hose clamps. Take off the old pump and install the new one. It is that simple. It is way more work to turn off the water, unscrew the dishwasher from the counter, slide the dishwasher out, turn it on it's side, then have to put it all back in, with the isulation.

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break.

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

1. Turn off the water.
2. Turn off the power to the dishwasher.
3. Pulled out the dishwasher.
4. Tilted it forward and to the side with a bowl to collect the water at the bottom.
5. Carefully laid the dishwasher on its side
6. Removed the existing pump. Make note of its orientation before removing (maybe take a picture). Disconnect the wire and loosen the 2 pipe clamps used to attach the pump. The pipe clamps were not the adjustable, reusable kind but the replacement part came with several.
7. Put the new pipe clamps on the hoses (the supply and discharge side) so they're in place.
8. Installed the replacement pump by pushing it on to the supply then the discharge hoses.
9. Move the clamps into place and tighten.
10. Reconnect the power wire.
11. Stand the dishwasher up.
12. Turn on the power and water.
13. Run a quick test to make sure it's working and doesn't leak.
14. Push it back in to place and reattach it to the cabinets.

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Twist counter clockwise to remove clockwise to install

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

Simply twist on the new part/filter.

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Process of elimination and a visit to my local repair store told me it was wise to try the tub gasket, and according to partselect.com, it solved the problem a majority of the time. My local repair dealer agreed: Try it. They agreed because for them to replace a lower door gasket AND the $10 tub gasket... if they came out, the service call and parts would equal half the cost to replace the whole dishwasher. So I bought a tub gasket from partselect.com and replaced the old one. It worked, it was easy, so if your same make & model is leaking? Try it first. That's my advice.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.