GDT655SGJ5BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Neil from NEW YORK, NY
- Parts Used:
- WD08X22095
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher door was leaking at bottom.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- louis from ROCKTON, IL
- Parts Used:
- WD28X20164
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower rack was broken/ rusted
Just snap part in position quick to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brant from LAS VEGAS, NV
- Parts Used:
- WD28X30227
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Old rack rusting is several areas
Bought replacement rack transferred all the accessories from the old to the new. Mostly snap-in-place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from SUMMERVILLE, SC
- Parts Used:
- WD21X31902C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
No power at display panel
I ordered the part recommended.Replaced,still no power.The next part was going to be another $175.00.It was better to stop and get a refund than put $300.00 into a six year old.dishwasher.I should be getting a refund any day now.Parts select was very helpful in that regard.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from EAST SYRACUSE, NY
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
No power indications to top UI board
Diagnosing was probably the most difficult, as I am an experienced electronic tech for 40 years. through research i found that the schematics and service paperwork was included with my dishwasher mine was located in the front left corner of the frame behind the kick panel. These service instructions were ok for guide but not really helpful in troubleshooting this fault. I found online the pinout output voltage from the main control board needed to be checked. however, this is not very easy to get a proper reading safely in such an awkward position. I ultimately scored the insulation back enough to get a set of clip leads and connect to my meter and obtain a reading. In my case there was voltage. I ordered the board and it arrived quick and installed. I cut and spliced together the wires I scored to make a reading but added an extra length of wire for service testing in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from OCEANSIDE, CA
- Parts Used:
- WD28X30227
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Wanted to replace original rusted top rack of dishwasher
Needed GE Technician to install. Partselect.com had to send a second replacement rack because the first one was defective. When the second on arrived, IT TOO WAS DEFECTIVE. After the Tech tried to install the second replacement, he was forced to remove a part from the original rusted rack in order to get the 2nd replacement to even stay in the rails of the machine. Tech was great, but the Partselect.com parts were unusable as sent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from ANGIER, NC
- Parts Used:
- WD18X22842
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Leak pan was missing upon new installation
Due to the almost zero clearance between the recirculating pump and the floor, getting the pan to line up and engage the tabs on the dishwasher frame can seem to be an impossible task. I did accomplish the task as instructed in the owners installation manual once.
However, I observed that the leak was just a drop at a time only on the deep clean mode where water recycling was in constant use during a long wash cycle. So, I recommend to slide the pan in the relative position without trying to engage the tabs and you will still accomplish the reason for the leak pan. Remember, the purpose of the Leak Pan is to protect your floor, so use it the easy way as I am.
However, I observed that the leak was just a drop at a time only on the deep clean mode where water recycling was in constant use during a long wash cycle. So, I recommend to slide the pan in the relative position without trying to engage the tabs and you will still accomplish the reason for the leak pan. Remember, the purpose of the Leak Pan is to protect your floor, so use it the easy way as I am.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from LANESVILLE, IN
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Delivery
The part has been sitting at a FedEx place for over a week and no one answers my emails about why. This is all I get: "No scheduled delivery date available at this time."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MONMOUTH BCH, NJ
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control board would not properly work and light up
Followed a u-tube video to remove dish wash door assembly to get to the control board . Not too hard if you are mechanically inclined.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from NEOSHO, MO
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
No power to the control panel
Removed the door to get to the UI control panel. Followed the instructions to set the jumpers to my particular model and put it back together. Fixed the issue and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!